Could 4-Way Trailer Wiring Harness be Used to Power Taillight Circuits of 7-Way

Question

Question:

Can tail light converter 118379 be used to tie into a seven way trailer plug? I have a 2002 Toyota Tacoma and have a seven way for trailer brakes. Was wanting to cut the four way plug off 118379 and tie into the same wires on the seven way. Thank you, hope I explained what so you understand what I am needing.

asked by: Randy B

0

Expert Reply:

Yes you can use the # 118379 as a way to power the taillight circuits of a 7-way. It would be just a matter of cutting off the 4-way and wiring to the correct pin on the 7-way like you can see in the attached picture.

expert reply by: Jameson C

0

7-way diagram
(click to enlarge)

Answer 1

Depending on how the trailer was made, there will be a few spots you can check to identify the axle. First, if the trailer was pre-made by a specific company, you may be able to find this information in either the paperwork or on a placard somewhere…

view full answer...

Answer 2

You will need to do some measuring to determine if the 10 Inch Electric Brake Assembly LH, item #AKEBRK-35L, is the correct assembly for your trailer. Measure the diameter of the mounted brake shoe, the width of the lining and the distance between…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 6

The correct replacement for a Demco Master Cylinder 05680-C is the Replacement Master Cylinder part #5650. I spoke with Demco to confirm this for you.

view full answer...

Answer 7

The correct replacement master cylinder kit we have for your Demco setup is the part #DM5918 which comes with the lock out replacement.

view full answer...

Answer 8

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 11

Based on my research, the Trailer Hub and Drum Assembly - 8,000-lb E-Z Lube Axles #AKHD-865-8-EZ-K will be a replacement for the 90865 Rockwell hub and drum. Both of these hub and drum assemblies are 12-1/4" diameter, have an 8,000 lb capacity,…

view full answer...

Answer 12

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Could 4-Way Trailer Wiring Harness be Used to Power Taillight Circuits of 7-Way

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching