Recommendations For Adding A Brake Controller To A 2009 Mitsubishi Outlander

Question

Question:

Hi I am looking for the brake light controller for my trailer, that is compatible with my 2009 Mitsubishi Outlander. Any help would be greatly appreciated

asked by: Gerardo M

0

Expert Reply:

To get your 2009 Mitsubishi Outlander set up to tow a trailer with brakes, you will need a few things. We do have all these things and I did include a few install videos for you to check out, so let's get into it.

First you will need a 4 Flat, like the Tekonsha T-One Vehicle Wiring Harness # 118518. If you already have a 4 Flat, you can skip to the next part, but if you do not, it will be required. This will supply the needed power to the turn signal, brake lights, and running lights and get you 1/3rd of the way there.

Next you will need to upgrade the 4 Flat to a 7 Way. For this you will need the Universal Installation Kit for Trailer Brake Controller # ETBC7. This will piggyback off the 4 Flat, but you will need to run a few wires up to the battery and cab of the vehicle to get it up and running. It will include all the needed wiring, circuit breakers, brackets, and the 7 Way plug, which does also have a 4 Flat plug on the side so you will not need an adapter if you every pull a smaller trailer that doesn't have brakes. Once this is all run, you can move on to the next part.

As to the final part; the brake controller. We do have a lot of options for these, but the Redarc Tow-Pro Elite # RED44FR is one that I highly recommend and would be the controller I would go with if I had the need for one. Once installed, only the adjustment/manual override knob will visible so it has a super clean look. It can also handle up to 6 brake assemblies (3 axles) and will work with electric or electric over hydraulic brake systems, so its versatile.

expert reply by: Lazer S

0

Answer 1

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 2

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 3

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 9

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Recommendations For Adding A Brake Controller To A 2009 Mitsubishi Outlander

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching