Which Fifth Wheel Hitch Wedge to Use with Pro Series Fifth Wheel Hitch

Question

Question:

I have a Reese Pro Series 20K 5th Wheel Hitch. I want to use it with a Factory instaled Reese Revolution Pinbox. What Wedge should I order? Thanks You...

asked by: Bill A

0

Expert Reply:

For your Pro Series fifth wheel hitch the wedge part # RP44FR is the correct one to use with a Sidewinder.

expert reply by: Jameson C

0

Answer 1

The only cushioned/extended pin box we have that will replace the Lippert 1116 pin box and provide more than 23-1/4" from the rear most bolt holes to the center line of the kingpin is the 5th Airborne Premium 5th Wheel Air Ride King Pin w/…

view full answer...

Answer 2

From what I was able to find with my research, the Hensley TS3 Trailer Saver 5th Wheel Hitch will fit into industry standard 5th wheel rails. I've attached a picture that shows the mounting hole dimensions on what are considered the industry…

view full answer...

Answer 3

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 4

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 5

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 6

Great question, Jeff! When the Rota-Flex first came out it renovated what a pin box could do and be, but at this point in time that technology is a little more dated and the Gen-Y Hitch Shock Absorbing 5th Wheel Pin Box #325-GH-8040 is the "new…

view full answer...

Answer 7

Most fifth wheel rails are made to the same industry standard dimensions. They aren't all though. If you measure 22 inches on center between the two rails and they look like the rails of the #RP30035 that you referenced they would be the industry…

view full answer...

Answer 8

Hi James, To my knowledge the Reese Goosebox is the only replacement option that won't void the frame warranty. That being said, the frame warranty is typically only a year so you really aren't losing much voiding it, especially if you've…

view full answer...

Answer 9

The Ram OEM 5th wheel puck system, shown in the linked photo and article, was launched in 2013 so what you have in your truck is likely to be an aftermarket installation of some kind. These newer Ram trucks with the factory prep can directly accept a…

view full answer...

Answer 10

Hi Joe, I assume you are referencing an Equal-i-zer weight distribution since you have shank #EQ90-02-4700. I went ahead and read the owners manual for their systems and there is noting regarding adjusting the angle of the hitch ball. The hitch head…

view full answer...

Answer 11

Thank you for the photo of your 2016 Ram 3500's bed rail which sits 59-inches above ground. You are correct that the recommended minimum clearance between a bed rail and the underside of the trailer's overhang is 5 to 6-inches, as shown in…

view full answer...

Answer 12

The Patriot Slider part #BWRVK3270 might be a bit more noisy than the Companion slider part #BWRVK3400 due to the increased number of mounting points, 4 at the corners vs. 1 in the center. Probably not that noticeable and certainly not something…

view full answer...

Which Fifth Wheel Hitch Wedge to Use with Pro Series Fifth Wheel Hitch

Products Referenced in This Question

Continue Researching