What Clamps do I Need to Mount My 1.8 Pound Aftermarket Lights to My Westin HDX Grille # 57-3705?

Question

Question:

I bought a hdx brush guard from you an want to add a set of Ridge Dually xl lights model 32221 to it? they weigh about 1.8 lbs each. Will your light clamp kit allow me to add these lights to my hdx brush guard without vibrating?? thanks

asked by: Dennis M

1

Helpful Expert Reply:

I just looked up your information and discovered that you ordered the Westin HDX Grille Guard with Punch Plate - Black Powder Coated Steel # 57-3705. If you are looking to add the universal light mounts for HDX grille guards # 57-0005 (black) or # 57-0000 (stainless steel), you will be fine with mounting two 1.8 pound Ridge Dually XL lights (without vibrating) as long as the bolt that mounts the light is does not exceed 1/2 inch diameter. I went ahead and attached a diagram that shows this measurement.

expert reply by: Bob C

1

Universal Light Clamps for Westin HDX Grille Guard # 57-0005 and # 57-0000 Mounting Hole Size for Aftermarket Lights
(click to enlarge)

Answer 1

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 2

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 3

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 4

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 5

The best option we offer for your dump trailer is the Erickson Mesh Tarp and Truck Bed Cover part #EM57059 which measures 12' wide x 16' long. It's not the exact dimensions you wanted but it will still cover most of the area you need it…

view full answer...

Answer 6

For a standard replacement equalizer for your Dexter 13-122 equalizers you'd want the #TREQE1 or for a cushioned version you'd want the part #K71-653-00 which comes with new shackles and bolts. For a kit that includes new bolts, bushings, and…

view full answer...

Answer 7

While we do have bumper/grille guards that fit your 2022 Toyota 4Runner Trail edition, we do not carry any guards that do not interfere with your front sensors. We have a few different models available. For something rugged looking, I recommend the…

view full answer...

Answer 8

The punch plate refers to the mesh looking section at the top of the grille guard. I attached a picture with it pointed out.

view full answer...

Answer 9

I checked the install instructions for the Westin HDX grille guard part #57-3835 you mentioned which fits your 2016 Ford F-150 and the tow hooks do need to be permanently removed. If you found yourself in a situation where you were stuck and you…

view full answer...

Answer 10

The problem isn't that you have a Tundra because you can install a fifth wheel rail kit #RP50084-58 into your 2012 Toyota Tundra without a problem. Any industry standard fifth wheel hitch will fit into the rail kit. The problem you'll run…

view full answer...

Answer 11

Yes, there is hitch receiver for your 2021 Tesla Model S, provided that it is not a Plaid or post refresh model. The EcoHitch Stealth Trailer Hitch Receiver - Custom Fit - 2", part #306-X7201, fits all Model S trim levels. This hitch receiver…

view full answer...

Answer 12

I went out to the warehouse and pulled trailer coupler #CA5400 to measure the latch width and its hole diameter. The latch outside width is just over 7/8 of an inch at 0.88 inches. And the hole diameter is just over 5/16 of an inch at 0.32 inches. If…

view full answer...

What Clamps do I Need to Mount My 1.8 Pound Aftermarket Lights to My Westin HDX Grille # 57-3705?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching