Do You Offer a 13-1/8" Long Equalizer for 2" Slipper Springs Without any Hardware?

Question

Question:

Can u get ap216 without the bolts etc Just the equalizer

asked by: Bob

0

Expert Reply:

The Equalizer from the Tandem-Axle Trailer Equalizer Kit for 2" Slipper Springs # AP216 is available without the hardware.

The Equalizer for 2" Wide Slipper Springs # TREQ1344 is what you are looking for.

expert reply by: Bud M

0

Answer 1

If you have 2 inch wide 7k slipper springs like the part #e74SR and your current axles are 38 inches apart on center the hanger kit part #HAP-105-205-01 that you referenced would be what you'd need.

view full answer...

Answer 2

There isn't a specific distance the hangers have to be for hanger kit #AP216-H238. A good place to start is 30-1/2 inches on center but you would only really know by mocking it up on the trailer before permanently installing the hangers. To…

view full answer...

Answer 3

The only reason that I can see that those tabs would have been welded onto your frame is to restrict articulation of the equalizer. And the only reason I would see anyone putting those on is if the articulation was causing the tires to contact the…

view full answer...

Answer 4

The equalizer in the Tandem-Axle Trailer Equalizer Kit #AP216 is 11-1/2" on center from the outer spring mounting holes when measuring horizontal separation. One hole will be 6" on center from the equalizer mounting hole center and the…

view full answer...

Answer 5

The hanger spacing for a tandem axle trailer suspension setup can be determined, but you need to take into account the axle spacing needed for the overall diameter of your wheel and tire combination and the springs you will be using. Lets say that…

view full answer...

Answer 6

I have a few things for you to check when it comes to not being able to pair your iPhone with the Curt Echo #C51180. The first thing to do is make sure that you're pairing your phone with the Echo through the app. If you paired it through the…

view full answer...

Answer 7

According to my contact at Fantastic Vent the correct replacement lift motor to use in your vent is part #FVK6010-81, not item FVK-6050-80. The replacement motor does operate at a higher 17-RPM speed. Since your fan is of a lower rpm and manufactured…

view full answer...

Answer 8

If you have already added the fuse and the trailer charge circuit is not activated in the 2019 Ford F-350 Super Duty with factory integrated brake controller, then you want to make sure the trailer is connected and you press the brake according to a…

view full answer...

Answer 9

I took a look at the owner's manual for a 2019 GMC Sierra 1500 Denali and both it and the standard 1500 can be flat towed so long as it is a four-wheel drive with a two-speed transfer case, and according to page 236 of the manual, "To shift…

view full answer...

Answer 10

I recommend going with the Curt Trailer Hitch Receiver #C11424 for your 2017 Hyundai Elantra as long as it's a Sedan (excluding the Sport edition). I like the Curt hitches because they tend to have a thicker powder coat which helps to protect…

view full answer...

Answer 11

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 12

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Do You Offer a 13-1/8" Long Equalizer for 2" Slipper Springs Without any Hardware?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching