Recommended Replacement Tarp For An Extang Full Tilt 8710 On A 2000 Ford F-150 Short Bed

Question

Question:

Replacement for 2000 f-150 61/2 ft bed full tilt with snaps? My old packing slip says item 8710 for original kit purchase Thanks!

asked by: Bryon

0

Expert Reply:

The replacement tarp for the Extang Full Tilt 8710 on your 2020 Ford F-150 with 6-1/2 foot bed will be the # EX5710. This is a direct replacement but does require the original hardware and rails for installation.

expert reply by: Lazer S

0

Answer 1

The #EX5940 you mentioned is actually meant to fit GM trucks and won't work with your 2006 Ford F-150. Instead, take a look at the: -Replacement Tarp for Extang FullTilt SL Soft Tonneau Cover #EX37615. This is the correct replacement tarp…

view full answer...

Answer 2

The correct replacement tarp will depend on whether your existing tonneau cover uses the snaps or if it's snapless. For the snapless version, use #EX37410. If it's the version with the snaps, you'll need #EX5410.

view full answer...

Answer 3

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 8

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 9

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 10

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 11

We do have the Rhino-Rack Masterkey Lock Barrels #RRRK093-2 which will provide you with 2 new lock cores and keys for your Rhino-Rack Zenith MasterFit Rooftop Cargo Box #RRRMFZ66. As far as pricing goes on the different sets they can change based on…

view full answer...

Answer 12

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Recommended Replacement Tarp For An Extang Full Tilt 8710 On A 2000 Ford F-150 Short Bed

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching