Hardwiring a 4 to 7-Way Adapter to Install a Brake Controller on a 2004 Nissan Pathfinder
Question:
I ordered the Tekonsha Prodigy P2 brake controller with the harness adapter for Nissan - I have a 2004 Pathfinder. I have a factory tow package, but it appears to just be a 4-pin. I have a 7-pin plug Its a 4 to 7 adapter plug, so the three wires that dont plug into the 4-pin harness are currently not going anywhere. With the supplied Nissan harness that comes with the brake controller, where do I run those three wires coming off the 7-pin plug?
asked by: Tom N
Expert Reply:
The remaining 3 wires on the adapter you are using will need to be hardwired in. You will need to use some wire, # 10-2-1, about 20 feet (the wiring is sold in increments of 1 foot), and you will need a 40 amp circuit breaker # PK54540.
On the adapter you should have a black wire and a blue wire that you can wire first. Use the duplex wire and attach the black to black and the white to blue. Then you will route the wiring under the vehicle towards the front. Be sure to avoid any hot or moving parts that could damage the wire.
Route the wiring up into the engine compartment and separate the black and white wires. The black wire will connect to the positive battery terminal via the 40 amp circuit breaker that gets mounted to the wall of the engine compartment near the battery. The white wire will need to be routed through the firewall, either through an existing entry point or hole you may need to drill.
In the cab of the vehicle, sever the blue wire from the brake controller harness just before it enters the plug that connects to the vehicle. Connect the end of the blue wire coming from the brake controller to the white wire you ran.
ALTERNATIVE: You can also check the connector where the existing 4-pole plugs into the harness on the frame rail. Look for a blue brake output wire on that harness. If it is there, you will not have to run that white wire all the way up, just connect it to that brake output wire. You also would not sever the blue wire on the wiring harness.
The last wire on the adapter is for reverse light. You will just tap into a reverse light circuit behind one of the tail lights. Or if the trailer does not require reverse lights you can tape it up and stow it out of the way.
I have included a link to an FAQ article that will help. Not all of the steps apply to your installation so just follow the ones that do.
Products Referenced in This Question
Deka Jacketed 2 Wire, 10 Gauge, Brake Wire - per Foot
- Wiring
- Wire
- Jacketed Wire
- 2 Wire
- 10 Gauge
- Deka
more information >
Pollak Circuit Breaker - Cycling/Automatic Reset - 40 Amp - Straight Mount Bracket
- Accessories and Parts
- Wiring
- Circuit Breaker
- 40 Amp
- Pollak
more information >
Product Page this Question was Asked From
Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers - Nissan and Infiniti
- Accessories and Parts
- Trailer Brake Controller
- Wiring Adapter
- Plugs into Brake Controller
- Vehicle Specific
- Tekonsha
more information >
Featured Help Information
Instructions
Miscellaneous Media
Continue Researching
- Q&A: Trailer Suspension Hanger Kit for Slipper Springs and 38 inch Wheelbase
- Q&A: Replacement For Fulton Drop-Leg Stabilizer Jack
- Article: Harvest Hosts
- Q&A: Does Furrion Single Zone Controller part # FACC12SA-BL Have Dip Switches
- Article: 5 Things to Know About Weight Distribution Hitches
- Article: 2 Steps for Finding the Right Weight Distribution Hitch Size
- Q&A: Charging Auxiliary Battery from Car Cigarette Lighter or 12 Volt Auxiliary Plug Connector
- Q&A: How Much Slack Is Needed In Trailer Wire Connection To The Tow Vehicle?
- Q&A: Replacing Integrated Brake Controller of 2008 Ford F-350
- Q&A: Recommended Replacement For A Dometic Duo-Therm Rooftop Unit
- Article: Brake Controller 7- and 4-Way Installation Kit (ETBC7)
- Article: Trailer Tire Sizing
- Article: The Differences Between Cam Buckles and Ratchet Straps (And Who Would Win In a Fight)
- Article: How to Store a Travel Trailer/Camper for the Winter