Which Charging Profile for Redarc BCDC to Charge Deep Cycle Battery

Question

Question:

I have the RED96FR My travel trailer has 2 Interstate deep cycle group 24 batteries. I have the Redarc on 14 .6 volts. Would the 15 or 15.3 be better?

asked by: David C

0

Expert Reply:

For a deep cycle battery I would keep your # RED96FR setting on the A profile at 14.6 volts. The higher voltage settings are for lithium batteries which require the higher voltage to charge.

expert reply by: Jameson C

0

Answer 1

My contact at Performance Tool said that the amount of amps that the 6" Oscillating Fan 12-Volt #PTW1658 draws is 1-1/2 to 2 amps. I have attached a review video that you can check out as well.

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

Typically a trailer axle will have some camber in it - some bend - such that when it is not loaded the tops of the wheels bow outward slightly, with the outside edges of the tire treads making first contact with the ground. This allows that when the…

view full answer...

Answer 4

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 5

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 8

The UFP H-1377 correlates to a Dexter #84 spindle, which is for a 3,500 pound axle. This will utilize an inner bearing #L68149 and an outer bearing #L44649. As this is being used on a boat trailer, I highly suggest going with the etrailer.com…

view full answer...

Answer 9

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 10

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 11

After you've packed the bearings and assembled everything, carefully slide the hub assembly onto the spindle and install the outer bearing. Install the spindle and tang washer and run the spindle nut down finger tight, then rotate the hub back…

view full answer...

Answer 12

The Dexter Nev-R-Adjust electric trailer brakes can be manually adjusted. There are a couple teeth of the adjustment wheel that are exposed just under the lever that you referenced. I have attached a photo showing the teeth. You will likely need a…

view full answer...

Which Charging Profile for Redarc BCDC to Charge Deep Cycle Battery

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching