Towing Mirrors for 2013 Ford Expedition

Question

Question:

Will this fit a 2013 Fire Expedition perfectly?

asked by: B

0

Expert Reply:

The CIPA Custom Towing Mirror, # 10300 will fit factory mirrors that look like the mirror in the attached image.

My recommendation of towing mirrors for your 2013 Ford Expedition is the K-Source Clip on Towing Mirrors, # KS3891-2. These are a universal mount mirrors, and as long as the mirror glass is recessed a bit into the mirror housing, the ratcheting rubber straps will cinch the mirror tightly to your mirror housing.

expert reply by: Michael R

0

10300_display
(click to enlarge)

Answer 1

Looking at pictures online of your 1989 SE Vixen Motorhome it appears that it has pretty standard factory rear view mirrors with which the K-Source Universal Towing Mirrors #KS3891-2 should work great. I really like these particular mirrors because…

view full answer...

Answer 2

The length of the arms on the K-Source Custom Towing Mirrors - Manual - Textured Black - Pair #KS62169-70G is 16" just like your existing mirrors. These are a direct replacement for the 25894030 and 25894029 OEM side mirrors. I have attached…

view full answer...

Answer 3

The Chevrolet box trucks were typically built on a 1 ton express van chassis. The K-Source Custom Extendable Towing Mirrors, #KS62077-78G, that you referenced were designed to replace the OEM mirrors on the 2007 to 2009 GMC Sierra and Chevrolet…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 11

Hey Shawn, yes the Air Lift Single Needle Gauge Panel part #AL26161 does have a light built into it. The spade connectors on the back of the gauge you'd run to the running light circuit which will light up when headlights are on.

view full answer...

Answer 12

Yes we do have a set of Timbrens that fit your 2024 Toyota Tundra with the part #T45MR. These can give you up to an additional 6,000 lbs of suspension support.

view full answer...

Towing Mirrors for 2013 Ford Expedition

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching