Socket Size of the Stromberg Carlson Manual Crank Handle

Question

Question:

Hi, I was just wondering what the socket size is for this handle # SC94VR. I do not know what jack I have but it would take a 7/16 socket to fit the jack. Does the handle have that size end on it? Thank you

asked by: William K

1

Helpful Expert Reply:

I contacted the manufacturer about the size of the Replacement Manual Crank Handle for Stromberg Carlson Electric Trailer Jacks # SC94VR. They were able to confirm that the handle is in fact a 7/16 socket.

expert reply by: Scott S

1

Answer 1

Since you have a Ram brand electric trailer jack the correct replacement manual override crank is the part #EJ-3520-HD that you referenced which is the correct size of 10 mm.

view full answer...

Answer 2

The Replacement Manual Jack Handle for etrailer or RAM Electric A-Frame Jack #EJ-3520-HD is a 10mm socket. As far as your jack making a clicking noise, it could be a few things. First check the ground connection on the motor and ensure it is grounded…

view full answer...

Answer 3

It sounds like you're wanting a CAD of the Replacement Manual Crank Handle for Stromberg Carlson Electric Trailer Jacks #SC94VR. Unfortunately we don't have those but I can tell you that the crank handle fits the following Stromberg Carlson…

view full answer...

Answer 4

We don't carry the Fastec FIC-3500 electric tongue jack or parts specifically for it. From what I read in online forums both parts and documentation for this imported jack are hard to come by. I was able to find the owner's manual online but…

view full answer...

Answer 5

The Replacement Glass Top for Furrion 2-in-1 Range Oven part #C-FSRE21SA-SS-003 is what you need to replace the glass top on a Furrion 2-in-1 Range Oven (FS17WB4A-BL) which is the same as our Furrion 2-in-1 Range Oven part #FSRE17SABL that is now…

view full answer...

Answer 6

The Replacement Override Nut #LC55FR that you referenced is made of steel.

view full answer...

Answer 7

It sounds like you may be needing the Replacement Override Nut for Lippert Electric Trailer Jack #LC55FR. If you're needing something different, I would be glad to assist you further.

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Socket Size of the Stromberg Carlson Manual Crank Handle

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching