Trailer Connector/Wiring Harness for 2021 Subaru Ascent

Question

Question:

Which trailer wiring harness is needed for a 2021 Subaru Ascent? I already have the # C25VR hitch.

asked by: Bryce

0

Expert Reply:

The correct wiring harness needed will depend on the type of trailer you're wanting to pull.

If you're pulling something basic like a small utility trailer and only need a 4 pole trailer connector, the # 118790 would be what you need.

However, if your trailer has a 7-way trailer connector, you'll need the # 118290.

expert reply by: Mike L

0

Answer 1

Due to the thinner gauge wiring of the #118290 for the 12 volt accessory circuit you'd be limited to the 20 amp charger for your battery.

view full answer...

Answer 2

There are two different 7-way trailer wiring harnesses for a 2019 Subaru Ascent dependent on whether or not you have the factory tow package. If you do have the factory tow package then you should be using the Tekonsha OEM Replacement Vehicle Wiring…

view full answer...

Answer 3

Yes, we do have a wiring harness that has both a 7-way and a 4-way for your 2020 Subaru Ascent. However, you will need a 4-way connector on your car before this will work though. I recommend the Tekonsha T-One Vehicle Wiring Harness with 4-Pole Flat…

view full answer...

Answer 4

Your 2019 Subaru Ascent with the factory tow package does have wiring ready for the easy install of a brake controller but it does not have a brake controller. For that the P3 part #90195 is a really great option. All you need to install it is the…

view full answer...

Answer 5

If all of your signals are working there may be no need to connect the wire that is for the 12 Volt trailer power on the Tekonsha OEM Replacement Vehicle Wiring Harness with 7-Way Trailer Connector part #118290 but I can not advise you to do anything…

view full answer...

Answer 6

Yep, so long as your 2024 Subaru Crosstrek Wilderness is not a hybrid both the Curt and etrailer hitches will fit: - Curt Trailer Hitch Receiver #C13382 - etrailer Trailer Hitch Receiver #e98912 The only difference besides price is the finish; the…

view full answer...

Answer 7

The best hitch receiver for hauling a bike with your 2022 Subaru Ascent is going to be the Curt Trailer Hitch Receiver - Custom Fit - Class III - 2" item #C25VR. This hitch receiver mounts behind your rear bumper bar instead of below your…

view full answer...

Answer 8

The best 4-way trailer wiring harness we have for your 2019 Subaru Crosstrek is the Curt #C56040 mainly because of the quality and reliability of the converter box. It has the highest amperage rating of all of the options which allows it to be the…

view full answer...

Answer 9

To install a 7-Way harness on your 2023 Subaru Ascent, without the towing package, you will need two separate wiring harnesses because they don't make just one that'll do the job. The first harness you'll need is the Curt T-Connector…

view full answer...

Answer 10

The connector you are looking for to install the Curt trailer wiring kit part #C56040 on your 2019 Subaru Ascent is located behind the driver side rear panel in the cargo area. If you check out the picture I attached you'll see where to find it.

view full answer...

Answer 11

The difference between the Curt #C25VR and etrailer #e55ZR trailer hitches for your 2022 Subaru Ascent is that the etrailer hitch has a matte black finish that is a bit more robust than the Curt. The matte black finish does a better job at matching…

view full answer...

Answer 12

You are right to be concerned with the integrity of the vehicle's frame when it comes to towing and tongue weight capacities. The towing and tongue weight capacities of a hitch are just what that specific hitch is rated for and does not transfer…

view full answer...

Trailer Connector/Wiring Harness for 2021 Subaru Ascent

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching