Can I Get Lippert Replacement Motor #368471 For My 2009 Jayco Seneca Motorhome

Question

Question:

I’m looking for a motor the Lipitor people gave me the number of 368471 with the motor and gear assembly I was wondering if you guys have one of those or could help me out with it

asked by: Allen A

0

Expert Reply:

Yes, we can help you get this product. That part is the Replacement Gear Motor w/ MX2 Con. For Lippert Slide Out part # LC88UD, is the part you need for your 2009 Jayco Seneca Motorhome. .

I have included a product description below.

expert reply by: Mark Smith

0

Lipper Motor 368471 For Slide Out
(click to enlarge)

Lipper Motor 368471
(click to enlarge)

Lippert Motor 368471
(click to enlarge)

Answer 1

The part number on your Power Gear Slide-Out motor is actually 524908, for which the correct replacement is part #LC368200. I was able to confirm this with Lippert.

view full answer...

Answer 2

The correct bearing kit you need for a Dexter 3,500 lb axle is the part #BK2-100 which comes with the bearings, races, and seal needed plus a tang washer and cotter pin.

view full answer...

Answer 3

The bearing kit part #BK2-100 is a kit designed specifically for 3,500 lb axles like what your trailer has. This will work well for your trailer and comes with all of the needed bearings, races and seal. I attached an install video for this kit for…

view full answer...

Answer 4

I reached out to Lippert and found that the correct replacement for your Power Gear Slide out motor 524065 is the Replacement Slide Gear Motor Assembly for Power Gear Slides #LC387738. Thank you for the pictures, it makes it way easier to find the…

view full answer...

Answer 5

The Replacement Converter for Parallax/Magnetek or WFCO RV Power Centers #PD4645V is exactly what you need for your Magnetek 7300. We have checked with Progressive Dynamics before and this is what they told us is needed. The DC fuse board does not…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 8

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 9

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 10

Yes, the Timken Bearing Kit #TMK52VR will fit your 3,500 lb axle as it fits an standard #84 spindle. The only time this kit won't fit with a 3,500 lb axle is if the trailer/axle is made before the 2000's since that's about the time that…

view full answer...

Answer 11

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 12

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Can I Get Lippert Replacement Motor #368471 For My 2009 Jayco Seneca Motorhome

Product Page this Question was Asked From

Continue Researching