Does Adco Storage Cover 290-74843 Keep Rain Out on Sides of Trailer

Question

Question:

WILL YOUR COVERS KEEP THE RAIN OUT ON THE SIDS?

asked by: BOBBY L

0

Expert Reply:

Trailer storage covers, including the Adco Polypropylene Storage Lot RV Cover for Travel Trailer # 290-74843 aren't totally waterproof on the sides to completely keep moisture and rain off the trailer because it needs to be breathable. This way, wind can vent through to help keep the cover in place, and the small amount of moisture inside the cover will be able to escape so there isn't mold or mildew.

The Adco Polypropylene Storage Lot RV Cover for Travel Trailer # 290-74843 is for travel trailers that measure between 24'1" - 26' long, not including the trailer tongue.

expert reply by: Kyle S

0

Answer 1

The exterior length I'm seeing for your Oliver Legacy Elite Travel Trailer is 23'-6". The #290-74841 only goes up to 22' so it will be too short. I recommend the Adco Polypropylene Storage Lot RV Cover for Travel…

view full answer...

Answer 2

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...

Answer 5

When measuring for a trailer cover you want to measure from the front of the trailer box, not the tongue, to the rear including anything that is attached to the rear. This will include a spare or a ladder at the farthest edge at the rear of the…

view full answer...

Answer 6

I would use a protractor, see photo, place the protractor on the edge of the inside of one side of the trailer frame and the other inside edge of the trailer frame should be parallel with the 50 degree line on the protractor. Another way to verify…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

Waylon, it does look like the Dexstar Steel Mini Mod Trailer Wheel #AM20539 is the same thing as the Dexstar 17-233 wheels you're referring too. These are silver wheels with a 6 on 5 1/2 bolt pattern, a 0 offset, and are made in the USA.

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The B&W Companion OEM 5th Wheel Hitch w/ Slider for Chevy/GMC Towing Prep Package #BWRVK3775 you're looking at will work fine with your new Chevrolet Silverado. This hitch has 3 height adjustments so you'll be able to set the hitch height…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

Yes, the Extang E-Series Tonneau part #EX27UV does fit trucks that have spray-in bed liners and bed rail covers. The cover brackets can clamp to your bed rails without requiring trimming the cover as well.

view full answer...