Correct Replacement Bracket for 8,000 Pound GTW Fastway e2 Weight Distribution Hitch With Round Bars

Question

Question:

Does this replacement work with the e2™ Hitch - Round bar 8000lb?

asked by: James D

0

Expert Reply:

The Replacement Sway-Control Bracket for Equal-i-zer Weight Distribution - 6,000 lbs to 14,000 lbs GTW # EQ95-01-5600 is the correct replacement bracket for the Fastway e2 Weight Distribution # FA94-00-0800. This comes as one bracket, so if you need to replace both you will have to order two.

expert reply by: Robin H

0

Answer 1

I spoke with my contact at Fastway about the difficulty you're experiencing. The most common reason this happens is when the L-bracket bolts aren't tightened evenly. If the bolts aren't tightened so they're perfectly even, the link…

view full answer...

Answer 2

The bolts that hold the L brackets for the Fastway e2 Weight Distribution w/ 2-Point Sway Control - Round - 6,000 lbs GTW, 600 lbs TW #FA94-00-0600 need to be torqued to a specific setting which you can find in your installation instructions (as well…

view full answer...

Answer 3

Yes and almost yes...a lot of people refer to weight distribution systems as "equalizer hitches" in the same way that people refer to bandages as Band-Aids. Equalizer is a very well-known brand of weight distribution system that people are…

view full answer...

Answer 4

The Replacement Sway-Control Bracket for Equal-i-zer Weight Distribution - 6,000 lbs to 14,000 lbs GTW #EQ95-01-5600 is for one sway control bracket, not both. It will give you what you need for one side of the trailer frame.

view full answer...

Answer 5

We do! The part that you're looking for is found as #EQ95-01-5600 on our site.

view full answer...

Answer 6

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 7

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 8

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 11

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 12

What you need for your Isuzu NPR truck is a powered converter #C59236. It is compatible with incandescent and LED trailer lights. I have included a link to the installation instructions for you. This harness does require a direct connection to the…

view full answer...

Correct Replacement Bracket for 8,000 Pound GTW Fastway e2 Weight Distribution Hitch With Round Bars

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching