1997 Chevy S-10 Fleetside Extang Full Tilt Replacement Tarp

Question

Question:

Im looking for a Xtang Full tilt replacement tarp for a 97 s-10 standard 6foot fleetside bed. Is this the correct one to order? If not what is the model number?

asked by: Ben

0

Expert Reply:

I just spoke with my rep at Extang and he confirmed that the item # EX37560 is the full tilt replacement cover for your 1997 Chevrolet S-10 fleetside truck.

expert reply by: Jerred H

0

Answer 1

The Replacement Tarp for Extang FullTilt SL Soft Tonneau Cover #EX37355 is not the correct replacement tarp for your Extang FullTilt tonneau cover, instead you'd need the Replacement Tarp for Extang FullTilt SL Soft Tonneau Cover #EX37425.

view full answer...

Answer 2

The correct replacement tarp for the Extang FullTilt SL Soft Tonneau Cover - Snapless J-Strip on a 2005 Dodge Ram 1500 with 6-1/2' bed is part #EX37770.

view full answer...

Answer 3

I spoke to my contact at Pace-Edwards he said that when installing a replacement cover, like the Replacement Cover for Pace Edwards JackRabbit Hard Tonneau Cover #311-TRPT1472-2007, the typical way he recommends to keep the tension on the spring is…

view full answer...

Answer 4

There is a replacement cover that could work for you, but without a part number I would not be able to absolutely guarantee it. Having said that, the Extang FullTilt SL Soft Tonneau Cover - Snapless J-Strip - Hatch Style #EX38645 is a fit for the…

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

Installing the Union Tee #AL21838 with your #AL57575 will tie the pressure of the two air bags together. So yes, a shift in a very heavy load like a truck camper will potentially result in air being forced from one into the other. The reason I say…

view full answer...

Answer 7

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

I did some checking and basically the cutout bumper is the regular factory bumper. The Curt hitch, #C15312, will fit up tighter and a little more recessed, apparently the same way the factory hitch does if it were installed. Some people like the…

view full answer...

Answer 10

An oil seal like Redline part #9103309 installs in the back side of the hub (the side nearest the trailer's frame) with the sides or "legs" of the seal inserted into the hub's bore. This means that the flat metal surface of the seal…

view full answer...

Answer 11

I think the best way to explain how to install a grease seal like #10-9 is to take a look at the video I have linked. Go to about the 6 minute, 10 second mark. At this point in the video, our installer begins to install the seal in the back of the…

view full answer...

Answer 12

The confusion is that the two answer pages have two different hitches they are referring to. The #C15312 measures 2-3/4 inches from the mounting flange down to the hitch opening and the #C15313 measures 5-5/8 inches. I attached a picture that has…

view full answer...

1997 Chevy S-10 Fleetside Extang Full Tilt Replacement Tarp

Product Page this Question was Asked From

Continue Researching