Can the Handle on Pro Series A-Frame 2K Trailer Jack be Moved to the Opposite Side
Question:
I currently have a top wind jack that is worn out, and I would like to replace it with a sidewind jack. As shown in photos/video the handle is directly above one of the mounting holes. This would not work for my application, but if it could be installed 180 degrees from the normal position, it would. Can the gearbox, and/or handle be flipped 180 degrees?
asked by: Joel K
Expert Reply:
You could just turn the jack to place the handle where you want it. The Pro Series jack # PSRV20000103 uses the standard triangle mounting pattern so just turn it so that one of the other corners is pointing forward. You cannot move the handle itself or rearrange the gear box inside to move the handle so rotation the entire jack would be the way to go.
Product Page this Question was Asked From
Pro Series Round, A-Frame Jack w/ External Gearbox - Sidewind - 14" Lift - 2,000 lbs
- Trailer Jack
- Car Hauler
- Enclosed Trailer
- Utility Trailer
- A-Frame Jack
- Leveling Jacks
- Tongue Jacks
- Steel
- 1001 - 2000 lbs
- Sidewind Jack
- 14 Inch Lift
- Bolt-On
- Weld-On
- No Wheel or Foot
- Pro Series
more information >
Continue Researching
- Shop: Pro Series Round, A-Frame Jack w/ External Gearbox - Sidewind - 14" Lift - 2,000 lbs
- Shop: Sleeve-Lock A-Frame Trailer Coupler - Flip Latch - Black - 2" Ball - 7,000 lbs
- Shop: Demco Cast Head Coupler w/ Jack Hole - eZ-Latch - 2" Ball - A-Frame - Bolt-On - 10K
- Shop: Pro Series Detachable Footplate w/ Pin for 2" Diameter Jacks - 2,000 lbs to 5,000 lbs
- Video: etrailer.com Flat Lip Trailer Coupler Lock Review
- Video: Review of etrailer Trailer Lock - Coupler Lock - E98895
- Q&A: Replacement Coupler for Vintage 1958 Boat Trailer
- Shop: Demco A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Zinc - 2" Ball - Bolt On - 10K
- Shop: Demco 50-Degree A-Frame Trailer Coupler w/ Jack Hole - eZ-Latch - Zinc - 2-5/16" Ball - 21K
- Shop: Blue Ox Hitch Receiver and Coupler Latch Lock Set - Swivel Design - 2" Hitches
- Video: Pro Series Round A-Frame Jack Review and Installation
- Q&A: Recommended Sidewind A-frame Jack for Small Karavan Utility Trailer
- Q&A: Measurement From Outer Tube Of Pro Series 2,000 Lb Trailer Jack To End Of Handle
- Q&A: Short Trailer Jack Recommendation for a 7000 lb A-frame Horse Trailer for Tailgate Clearance
- Search Results: a~frame trailer jack
- Search Results: loading ramps
- Shop: Trailer Hitch
- Article: Trailer Wiring Diagrams
- Search Results: trailer jack
- Q&A: Lug Nut Torque Chart for Trailer Wheels
- Search Results: safety chains
- Q&A: What is the Difference Between a Class II and a Class III Hitch?
- Shop: Trailer Wiring
- Video: Timbren Axle-Less Trailer Suspension System Installation
- Article: Trailer Tire Sizing
- Article: How to Measure for Trailer Hitch Drop
- Q&A: How to Measure the Angle of Trailer A Frame To Determine if a 50 Degree A Frame Coupler will Fit
- Video: Choosing the Right Trailer Wiring
- Search Results: coupler lock
- Shop: Suspension Enhancement