Items Needed to Install Solera Awning

Question

Question:

Awning LC00211523 is it all complete and ready to mount

asked by: Jerry D

0

Expert Reply:

The Solera, # LCV000211523 is the awning roller and fabric. For a complete system the arms and awning rails are needed too. The Solera Manual Hardware Kit, # LC434727 and the Solera Rail Extrusion, # LC715217.

The manual hardware kit comes with the 69" arms in black and and include a crank rod to extend and retract the awning. Since the extrusion comes in 8 foot lengths (and you need at least 6" of extra space on both sides) you will need to order 3 of them.

expert reply by: Michael R

0

Answer 1

The roller tube assembly and awning for your Dometic brand awning can be replaced with the Solera 20' White Fade RV Awning Roller and Fabric (Std) #LCV000211523. This is a customer favorite, but there are many other colors available, so I've…

view full answer...

Answer 2

Awnings such as Solera 20' Sand Fade awning #LCV000231498 are not trailer-specific so they can be installed on pretty much any trailer. If your trailer does not have the metal channel for the awning to fit in they one will need to be installed.…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 6

The Lippert 2420801 hub is an 8k hub with an 8 lug bolt pattern so for a replacement you'd just need the part #8-285-10UC3-A.

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 9

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 10

When choosing the slider you want to measure the outside front of box width including the flange. Then you need to select a slider that extends a minimum of 2-1/2 inches beyond each side of the box width. For example, the Black Solera Slider…

view full answer...

Answer 11

Sorry Jennifer, I am a bit confused as you were looking at the Replacement U-Clamp Bracket #RM-B141 which mounts with bolts and not U-bolts. This part works with the Split Bushing #RM-205217-10 for the discontinued Roadmaster Front Anti-Sway Bar…

view full answer...

Answer 12

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...