2000 Four Winns Trailer Taillight Replacement

Question

Question:

My trailer lights just died and I am finding that the bulb capsule is no longer available, any suggestions for replacement size wise? Are replacement side marker lights available or should I just get a whole new wiring kit with everything?

asked by: Craig J

0

Expert Reply:

The capsules and the capsule style trailer lights are no longer available so you'd need to replace what you have with new lights that are similar like the part # 403076 for the passenger side and the part # 403026 for driver side.

expert reply by: Jameson C

0

Answer 1

Thank you for the pictures they do help. The Optronics LED Clearance or Side Marker Light - Submersible #MCL95AB you're looking at will work great as a replacement for your Four Winns Boat Trailer. This LED light is a 12V light that draws 12.8V:…

view full answer...

Answer 2

The Peterson Clearance and Side Marker Trailer Light #M152R will be the closest option we have for you. The 2 inch lens has male terminals on the back which accept a 2-wire female plug. If you need the Amber Light you will need the #M152A. If you…

view full answer...

Answer 3

I believe what you're referring to is something like the lights which come in the Optronics LED Tail Light Kit #TLL160RK. These measure 8-1/16" long x 2-7/8" tall x 2-13/16" deep and are submersible so they are perfect for your…

view full answer...

Answer 4

Yes, the Westlake ST225/75R15 Radial Trailer Tire #LHWL304 that you referenced will work great on your trailer that weighs 4,000 lbs. Each of these tires is rated for 2,830 lbs which means that even if your trailer was a single axle you'd have…

view full answer...

Answer 5

Trailer tires should be inflated when they are cold and should be inflated to the max psi rating on the sidewall. In your case you would want to run 80 psi. If you don't inflate them to the max psi figure you will lose weight capacity and…

view full answer...

Answer 6

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 7

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 8

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 9

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

Answer 10

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 11

The old version of the #HBA-CAM used 4 wires, but the product was updated awhile back and now uses only two wires as shown in the photo on the product description page. The white wire from the HBA-CAM would tap into the white ground wire and the blue…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

2000 Four Winns Trailer Taillight Replacement

Continue Researching