Can The NOCO Gen Battery Charger NOC94FR Charge 3 Lithium Batteries?

Question

Question:

Will this charge three lithium batteries

asked by: Will T

1

Helpful Expert Reply:

The NOCO GEN On-Board Battery Charger - AC to DC - Waterproof - 3 Bank - 12V - 15 Amp # NOC94FR does work with 3 lithium batteries as long as they have a BMS (battery management system) such as the The Manager30 Battery Management System with Lithium Profile # RED88FR.

A better option for you may be the OptiMate Lithium 4s Smart Battery Charger - AC to DC - 12V - 4 Bank - 0.8 Amps # MA97JR which works without a battery management system. It has built-in BMS protection and charges up to 4 lithium batteries at a time. I attached a demonstration video for this charger.

expert reply by: Andrew N

1

Answer 1

To charge your batteries on your 2015 Lance 1575 from your vehicle or solar power and that is compatible with lithium batteries, I recommend the The Manager30 Battery Management System with Lithium Profile Item #RED88FR and the Pollak…

view full answer...

Answer 2

Hey Doug, thanks for reaching out! The MORryde ALLTREK 4000 #MR89DR dimensions can be a bit difficult to explain via text so I've attached an image giving you the dimensions you're asking about!

view full answer...

Answer 3

Hey Paul, For the stainless steel version of part #SM78VR you'll just need the SmartPlug RV TV/Internet Inlet - 2 Coaxial Connector - Stainless Steel #SM58FR. This comes with two coaxial connectors but you can always pop one out and install an…

view full answer...

Answer 4

First, unless the coupler that you have is not functioning properly, does not couple to the ball, or is damaged, you do not have to change it out. It will still function just fine with electric brakes. I went out to the warehouse to determine the…

view full answer...

Answer 5

I went out to the warehouse to determine the mounting pattern of the Model 6 actuator and the coupler, #T4853100.I have included a picture below that shows the bolt patterns. The 2 holes are at 1.031 inches, the last 2 holes are at 1.25 inches and…

view full answer...

Answer 6

If your trailer has torsion axles, no worries but it it's a leaf spring suspension you really should have equalizers. Without the equalizer, the trailer will have a rougher ride and the weight won't be balanced across both axles when going…

view full answer...

Answer 7

It is possible but unlikely that a trailer manufacturer would use different size special trailer tires on the front and rear axles of one of their trailers. More likely is that a previous owner substituted alternate tires. We recommend that all tires…

view full answer...

Answer 8

You can pretty easily go from a 205/75-14 to a 15 inch tire size like 205/75-15 like with the #AM32395 without clearance issues. This will give you a slightly larger wheel and tire which will have a higher weight capacity. So you might gain a slight…

view full answer...

Answer 9

From the information that I was able to find on the L44549 bearing, it shows it being a 1-1/16 inch bearing which is the same as Trailer Hub Bearing, #L44649. Just to be sure, I recommend measuring the L44549 bearing with a digital caliper to confirm…

view full answer...

Answer 10

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Can The NOCO Gen Battery Charger NOC94FR Charge 3 Lithium Batteries?

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching