How Much Does the Trailer Valet RVR9 Remote-Controlled Trailer Dolly Weigh?

Question

Question:

How much does #9000 unit weigh?

asked by: David D

0

Expert Reply:

The weight of the Trailer Valet RVR9 Remote-Controlled Trailer Dolly item # TVRVR9 is 75 lbs.

expert reply by: Jerred H

0

Answer 1

I'm sorry to hear that your trailer dolly didn't work out as well as you had hoped. Since you plan to use the Trailer Valet RVR9 Remote-Controlled Trailer Dolly #TVRVR9 in areas that aren't always smooth and level, I would like to share…

view full answer...

Answer 2

In order to lower your 4,000 lb trailer down your driveway the only option would be the Trailer Valet RVR5 Remote-Controlled Trailer Dolly #TVRVR5. This dolly can handle a trailer up to 5,500 lbs and 550 lbs of tongue weight. It also works on slopes…

view full answer...

Answer 3

We do not sell refurbished versions of the Trailer Valet RVR3 Remote-Controlled Trailer Dolly w/ Hitch Ball Mount #TVRVR3-BB225 we only carry the brand new versions. We haven't seen enough failure from these to notice a trend of any of the…

view full answer...

Answer 4

When using the Trailer Valet with a tandem axle trailer it is recommended to use the Trailer Valet Trailer Wheel Dollies #TV56FR under the rear wheels. The dollies will provide you with much better turning radius, as the tires will try and bind up…

view full answer...

Answer 5

The Trailer Valet RVR9 #TVRVR9 is rated for a trailer up to 9,000lbs with a 900lb tongue weight. As long as your 8,000lb trailer does not exceed the tongue weight for this you will be able to move your trailer. We do have the Trailer Valet RVR12…

view full answer...

Answer 6

Past customers have told us the AL-KO 8460 uses inner bearing 25580 and outer bearing 15123, which would make the Timken Bearing Kit #TMK82VR the correct replacement bearing kit for that hub. If you are looking to replace the hub entirely the correct…

view full answer...

Answer 7

I reached out to TrailerValet and the #TVRVR9 you were looking at measures 6.53" from the center of the hitch ball to the front edge of the tracks as shown in the below diagram. You'll need to measure from the center of the coupler on your…

view full answer...

Answer 8

We do have a solution to mount the #288-07503 in what I'm assuming is an enclosed trailer. What you can use is the CargoSmart Rotating Safety Ladder Hook #CS57FR. You will also need E-track to be able to mount the hooks. If you want some single…

view full answer...

Answer 9

The best brake controller option to go with is one that activates the brakes proportionally instead of time delayed. A proportional brake controller will activate the trailer brakes at the same time and with the same intensity as the tow vehicle…

view full answer...

Answer 10

I would be happy to! The bottom of the foot to the center of the pipe mount is 10-1/2" when retracted and 24-1/2" when fully extended on the Trailer Valet JXS Trailer Jack w/ Footplate and Drill Powered Option item #TV64FR. Sorry I do not…

view full answer...

Answer 11

The Trailer Valet RVR3 - Remote-Controlled Trailer Mover #TVRVR3 that you referenced weighs a total of 45 lbs and and has a trailer weight capacity of 3,500 lbs. The higher rated #TVRVR5 weighs 99 lbs and has a 5,500 lb trailer weight capacity.

view full answer...

Answer 12

The crank handle of the Trailer Valet XL Trailer Dolly #TVXL25 can be spun in either direction so it could push or pull a trailer if needed. In either direction it works just as good.

view full answer...