Is There An Engine Block Heater For The 2021 Toyota Tacoma?

Question

Question:

Your website doesnt seem to have anything for either of the 2019,2020 or 2021 models.....it says no confirmation of fit....puzzling. Maybe the site isnt fully updated....so Do you have a block heater for a 2021 Tacoma V6 ?? Thanks

asked by: Guy B

1

Helpful Expert Reply:

I confirmed with the manufacturer that Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts # KH11813 will indeed fit your 2021 Toyota Tacoma V6. This installs very simply as you can see in the attached demonstration video.

expert reply by: Andrew N

1

Answer 1

Kat's does recommend coating the cartridge with NSCG silicone grease G-624 before inserting the cartridge heaters like the #KH11813 into the block.

view full answer...

Answer 2

I checked with Kat's about the correct engine block heater for your 2012 Toyota Tacoma with a 2.7L I4 engine, I confirmed that the correct fit is the Kat's Heaters Custom Engine Block Heater #KH11481. According to Kat's, this will install…

view full answer...

Answer 3

We haven't gotten a chance to make an install video of the Kat's Heaters Engine Block Heater #KH11813 on your 2018 Toyota RAV4 but I did check with Kat's to verify where exactly the cartridge will install in the engine block. The…

view full answer...

Answer 4

The Kat's Heaters Custom Fit Engine Block Heater - Cartridge Style - 120V - 400 Watts #KH11813 is a confirmed fit for the 3.5L V6. You should not need to alter the element or clip in any way and doing so is not recommended. You may want to…

view full answer...

Answer 5

You're correct, the Kat's Heaters Custom Fit Engine Block Heater #KH11813 is the confirmed fit for your 2018 Toyota Tacoma with a V6 3.5L engine. This block heater will need to be installed in the "FL" position on your engine…

view full answer...

Answer 6

For the 3.4L engine in your Tacoma, you'd want to use the #KH11482, which installs into the frost plug on the rear left of the engine block, per the diagram I've provided. The KH11813 won't fit your engine.

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

The Rhino-Rack Roof Rack for Factory Tracks #Y02-490B-NT is going to be your best bet for the tracks on the ARE topper for your 2012 Toyota Tacoma. The weight capacity is 220 lbs like you mentioned, but that's going to be the highest you'll…

view full answer...

Answer 11

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 12

I recommend the Redarc Tow-Pro Liberty Brake Controller #RED24FR for your 2023 Toyota Tacoma with the factory tow package. You will be able to connect the wiring using the Redarc Adapter #RED99FR directly to the factory connector. We also have the…

view full answer...

Is There An Engine Block Heater For The 2021 Toyota Tacoma?

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching