2014 Winnebago Vista35F 22k GVWR F53 Sway Bar Brackets and Bushings

Question

Question:

What is diameter stock rear sway bar, i need bushings and brackets. Thank You

asked by: Anthony P

0

Expert Reply:

The stock rear bar of your 2014 Winnebago Vista built on a Ford 22k chassis has a 1-3/8inch diameter which we have a kit for all new brackets and bushings with the part # RM-4139-300.

expert reply by: Jameson C

0

Answer 1

The Roadmaster Bracket for Anti-Sway Bar Split Bushings #RMB140 has mounting holes that are spaced out 3-1/4" center-to-center (see attached). This is designed to be a replacement part for the Roadmaster Front Anti-Sway Bar and Bushing Kit…

view full answer...

Answer 2

In order to replace just the factory anti-sway bar bushings on a Ford F-53 Chassis you have a few options which will be based on the location of the anti-sway bar (front/rear) and the gross vehicle weight rating of the coach (15,700 lbs, 16,000 lbs…

view full answer...

Answer 3

Yes, since your 2019 Ford F-53 motorhome has a sway bar with a 1-3/8 inch diameter the bushing kit part #RM-4139-300 would fit.

view full answer...

Answer 4

I recommend having your suspension checked out to make sure there are no issues, but if everything is fine, suspension enhancement springs would help level your Itasca. I could not guarantee this will "fix" your lean but the SumoSprings…

view full answer...

Answer 5

The correct SumoSprings that fit your 2020 Coachmen Mirada depends on what the GVWR is for your RV, but don't worry because we have a fit for all 2019 Ford F-53 options so you just need to choose from the list below (and/or let me know what model…

view full answer...

Answer 6

For an 1-5/8" diameter bar on your 2004 Country Couch Magna I recommend Roadmaster Bracket for Anti-Sway Bar Split Bushings Item #RMB140 and Roadmaster Split Bushing for Anti-Sway Bar - 1-5/8" Item #RM205222-10. It is a good idea to check…

view full answer...

Answer 7

For your 2012 Ford F-53, you can use the Roadmaster Polyurethane Bushing Kit for 1-1/2" Diameter, Factory Front Anti-Sway Bar #RM66ZR; these bushings will work great with the factory anti-sway bar.

view full answer...

Answer 8

The Hellwig Adjustable Big Wig Rear Anti-Sway Bar #HE94FR is only going to leave a few inches between it and the spare tire, as you can see in the attached picture. Depending on how far forward you have the tire it could potentially interfere with…

view full answer...

Answer 9

Roadmasters priority when it comes to their sway bars is top notch quality and the easiest install for the customer. This typically cuts the install time down enough that you end up saving money if you pay to have the bars installed or decide to do…

view full answer...

Answer 10

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 11

Hey David, actually what is going to make the biggest improvement in handling and stability for your 2011 Itasca is an upgraded rear sway bar with the part #RM-1139-175. I know that's not what you asked about but for motorhomes where most of the…

view full answer...

Answer 12

I'm assuming your 2024 F-250 has the 6-3/4' bed. If that is correct, the right tie-downs are in fact the #TLF3008 and #TL77CR. TorkLift has accounted for the bed access steps on the 2024 model and confirmed these will fit your truck.

view full answer...

2014 Winnebago Vista35F 22k GVWR F53 Sway Bar Brackets and Bushings

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching