Troubleshooting Fan-Tastic Roof Vent Remote that Won't Program

Question

Question:

Thanks for your response. After taking out the batteries and the fuse and letting everything sit for 2-5 minutes (we tried this six times so far), I still cannot get the manual and auto lights to flash. I have tried every combination of two arrows to try to get a reset. If it matters, there is no light shining out of the diode on the remote, although I can scroll through all the options with single arrows. I assume this means that I need a new remote. Does that seem right? Best,

asked by: Lynn R

0

Expert Reply:

Sounds like you tried to program the remote using the following instructions:

Hold your remote 12 inches away from the fan while holding both arrows. The Auto and Manual lights will begin flashing immediately. Continue holding both arrows down until the seven LED's flash once. Now it's programmed.

You may have to try both sets of arrows, the speed and temp ones.

Now I would try this if you haven't since it will reset the remote and circuit board:

1. Ensure that you have good batteries in the remote. 2. Verify that fan is working otherwise. 3. Pair the remote to the fan by a.) remove batteries for 2 minutes then install them again making sure to match polarity, b.) Remove the fuse from the fan for 2 minutes then install it again. c.) Hold remote control up to the fan and hold down the two arrow buttons. The arrow LED's will start flashing. Continue holding down until the seven LED's flash once after about 45 seconds.

expert reply by: Jameson C

0

Lynn R.

8/16/2021

Thanks for your response. After taking out the batteries and the fuse and letting everything sit for 2-5 minutes (we tried this six times so far), I still cannot get the manual and auto lights to flash. I have tried every combination of two arrows to try to get a reset. If it matters, there is no light shining out of the diode on the remote, although I can scroll through all the options with single arrows. I assume this means that I need a new remote. Does that seem right? Best,

Reply

Jameson C.

8/16/2021

Yes it would be time for a new remote then with the part # FV9068-09.

Reply

Answer 1

Have you tried reprogramming the remote? For programming a Fan-Tastic roof vent remote like part #FV9068-09 which is what your 7350 fan part #FV807350 uses what you need to do is hold your remote 12 inches away from the fan while holding both…

view full answer...

Answer 2

I have attached for you below a list of troubleshooting steps for the Fan-Tastic Vent Roof Vents like part #FV807350 which will vary depending on what symptoms your roof vent is having and what particular model you have. The remote reprogramming…

view full answer...

Answer 3

That does not sound fun to deal with, I have a solution for you though. It sounds like either the remote needs to be reset or you do not have proper voltage going to the unit. To reprogram the remote hold it at least 12 inches or closer to the…

view full answer...

Answer 4

In order to disable the rain sensor on a Fan-tastic Vent #FV803350 without a remote you can hold the "up/down" button on the unit for 3 seconds as opposed to the remote. You should get a beep or a double beep to confirm the sensor shut off…

view full answer...

Answer 5

The flow of propane can't be over-regulated unless the 2 different regulators restrict the flow at different amounts. Take a look at what your Weber grill requires and what your camper regulator is rated for (assuming that the regulator on the…

view full answer...

Answer 6

I can see why you would ask this question. Since Fantastic Fan is not very specific about which arrows, my only advice is to try the up and down arrows for both the speed and the temp separately until the remote programs. The programming process…

view full answer...

Answer 7

The only way to get the replacement circuit board for your Fan-Tastic Vent Roof Vent is through part #FV807359, which is essentially all the main internal components, including the circuit board, screen assembly, powered lift, as well as a new remote…

view full answer...

Answer 8

For programming a Fan-Tastic roof vent remote like part #FV9068-09 what you need to do is hold your remote 12 inches away from the fan while holding both arrows. The Auto and Manual lights will begin flashing immediately. Continue holding both arrows…

view full answer...

Answer 9

Sounds like there an issue with the circuit board of your Fan-Tastic roof vent which is preventing the remote from working. The only way to replace that on your 7350 is going to be with the part #FV807357 which comes with basically an all new inner…

view full answer...

Answer 10

After some internet research, it seems that others have tried and failed to find that elusive part also. Save time and trouble = replace both parts with the Camco #CAM59853 Quick Connect Kit. When making threaded propane connections, apply JR…

view full answer...

Answer 11

I would be happy to help! Starting with reprogramming the remote on your Fan-Tastic Vent Roof Vent w/ 12V Fan and Remote - Powered Lift - 14-1/4" x 14-1/4" #FV807350 you will need to hold the remote 12" away from the fan while holding…

view full answer...

Answer 12

This is a good question, but the answer is you'll have to try both sets of arrows when programming the remote part #FV9068-09, the speed and the temp ones as it can be either. For programming a Fan-Tastic roof vent remote like part #FV9068-09…

view full answer...

Troubleshooting Fan-Tastic Roof Vent Remote that Won't Program

Product Page this Question was Asked From

Continue Researching