Recommended Bolt Size To Install Lock N Roll 2-1/2" Articulating Trailer Coupler 336TS506

Question

Question:

Does the lock n roll 2 1/2” trailer side come with a bolt kit. If not can it be purchased separately?

asked by: Travis

0

Expert Reply:

The Lock N Roll Articulating Channel Tongue Trailer Coupler - 2-1/2" Channel - Trailer Side # 336TS506 you were looking at does not include bolts, but they can be purchased from a local hardware store.

The bolt holes in the # 336TS506 are 1/2" in diameter so you will need two 1/2" x 3-1/2" grade 8 bolts with four washers and a lock nut.

I included a video of the # 336TS506 for you to take a look at.

expert reply by: Samuel C

0

Answer 1

The Lock N Roll Articulating Channel Tongue Trailer Coupler #336TS528 that you referenced is designed to fit on 2 inch wide frame channel. If you need a version that fits a 3 inch channel you'd want the part #336TS508 instead. The 3 inch…

view full answer...

Answer 2

Yes, the Lock N Roll Articulating Trailer Hitch #336VS501 will allow you to backup your trailer just like a traditional ball hitch. Since the hitch and Coupler #336TS528 lock onto one another there is much less noise than you will get with a…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 8

There is a trailer coupler designed specifically to be used for offroading, from Lock N Roll. This uses an articulating connection between the coupler and accompanying hitch mount that gives a full 360 degree rotation between the two. So the…

view full answer...

Answer 9

We do carry the 33" Ark Stabilizer Jack that you are looking for with part #ARK77FR. I was able to track down a few drawings that you should find helpful. These are for the 30" #ARK94FR and the 24" #ARK34FR Stabilizer…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion…

view full answer...

Answer 11

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 12

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13…

view full answer...