Square Crossbar Roof Rack Fit For 2021 Nissan Rogue

Question

Question:

I have a 2021 Nissan Rogue with a flush mounted roof rack. I also have a Thule roof rack from a previous vehicle that used strap mountings on a raised roof rack and the square bblack load bars. My question. Is there a connector to the flush mounted roof rack that supports the square Thule load bars? The flush roof rack has 4 mounting points into which the connector feet need to be attached. I think these exist but the question is whether there is a model of connector that supports the older style load bars.

asked by: Roger G

0

Expert Reply:

Thule doesn't offer a square crossbar roof rack fit for the 2021 Nissan Rogue at this time, I'm sorry to say.

The only roof rack fits we offer are from Yakima, you could construct a roof rack using the following parts:

• JetStream 50 Inch crossbars, part # Y00425
• BaseLine roof rack towers, part # Y28TR
• Fit Kit, part # Y06179
• Fit Kit, part # Y06161

Yakima doesn't offer a fit kit that uses the fixed points in your Rogue's roof. The fit kits use clips that grab the inside top of the front and rear door jambs and use that to attach the rack to the vehicle. It's a very strong and reliable system that's been around for years.

expert reply by: Mike L

0

Answer 1

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The issue with this…

view full answer...

Answer 3

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 4

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 5

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 6

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 7

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 10

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 11

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 12

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Square Crossbar Roof Rack Fit For 2021 Nissan Rogue

Products Referenced in This Question

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching