Why Can't Lippert Solid Stance RV Step Support Kit be Used on Quad Steps

Question

Question:

why could i not mount these on the quad steps?

asked by: Tim J

0

Expert Reply:

The issue with the Lippert Solid Stance RV Step Support Kit # LC96BJ being used on quad steps is there just isn't clearance underneath them for how much space the # LC96BJ would take up. This adds about 1-1/2 inches of depth to the steps.

expert reply by: Jameson C

0

Answer 1

Yes, the temperatures you mentioned are normal. If you were getting over 200 degrees that would be a bad sign. But typically if all of the hubs are the same temperature you're good and it's only really an issue if one of the hubs is hotter…

view full answer...

Answer 2

Trailer tires always indicate their rated psi-pressure on the sidewall. Trailer tires should ALWAYS be inflated to this COLD psi rating under all conditions. It is never appropriate to under- or over-inflate a trailer tire for any reason, such as to…

view full answer...

Answer 3

I can end this debate for you real fast! Trailer tires, which will have an ST in front of the size, should always be inflated to the maximum psi indicated on the tire. Trailer tires usually do not have a recommended and maximum psi indication so I am…

view full answer...

Answer 4

I actually have a Lippert Solid Stance RV Step Support Kit #LC96BJ on the trailer I'm currently working on so I was able to get the following dimensions for you: Overall length including the feet facing outward: 23-1/4" Bracket length:…

view full answer...

Answer 5

Yes the Lippert Solid Stance RV Step Support Kit #LC96BJ that you referenced does fit the steps you have on your Winnebago Minnie Plus, 2019, 26RBSS. And based on the dimensions you have from the bottom of the step to the ground it would fit in that…

view full answer...

Answer 6

There are many options for attaching the breakaway cable from the Tow Ready Trailer Break Away Kit, item #50-85-315, to your vehicle. You could attach to a tie down point in the bed of your truck or you could use stake pocket tie down and attach the…

view full answer...

Answer 7

The Lippert Solid Stance RV Step Support Kit #LC96BJ will fit Lippert double and triple manual folding steps, and in regards to how it will fit, what you will need to do is check the space you have under your double step. You will need to have at…

view full answer...

Answer 8

According to Lippert, the #LC96BJ Solid Stance RV Step Supports can be installed to the lip on the rear of the bottom step, but it'll be more difficult to access the linch pins used to secure the legs in the up or down position.

view full answer...

Answer 9

What you're looking for doesn't really exist (yet) but there are options like the Lippert Solid Stance RV Step Support Kit #LC96BJ that you can add on to help support the step. I've attached a short video below going over how to install…

view full answer...

Answer 10

You could use air bags and weight distribution at the same time. But if you are experiencing rear end sag on the tow vehicle caused by towing a trailer then the best solution is weight distribution. But not just any weight distribution system. It has…

view full answer...

Answer 11

The overall dimensions of the Lippert Solid Stance Step Kit #LC96BJ that you referenced are 22-3/4" wide x 2-5/8" tall x 4-1/2" deep and the thickness is exactly 1-1/4 inches like you said you need.

view full answer...

Answer 12

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Why Can't Lippert Solid Stance RV Step Support Kit be Used on Quad Steps

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching