Replacement Support Arm for 69 inch Flat Style Awning Support Arm

Question

Question:

I have a 69inch flat style is the part number Lc281154 in black correct for my application I have a broken pump and bottom brace

asked by: Herm E

0

Expert Reply:

Yes, since you have the 69 inch flat style awning support arm the replacement you'd need is the part # LC281154 that you mentioned.

expert reply by: Jameson C

0

Answer 1

I reached out directly to Timbren for you, and they told me the correct fit for your 2021 GMC Sierra 1500 AT4 was indeed the Timbren Suspension Enhancement System #T28MR.

view full answer...

Answer 2

The Timbren Springs #T28MR has an overall height of 5-11/16". With your 2021 GMC AT4 having the factory lift you will want to measure the distance from inside the cup on your current jounce bumper to the pad on the axle. We do have a 1"…

view full answer...

Answer 3

Yes, the Timbren Suspension Enhancement System #T28MR will be the best option when it comes to cost-effectiveness. This will fit with your 2021 Chevrolet Silverado 1500 Z71 Trail Boss but you'll want to make sure these fit the gap properly. The…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Hey Dustin, thanks for reaching out! I will recommend SumoSprings over Timbrens all day everyday because they are much more forgiving when the vehicle is unloaded. We've actually joked around here about how the Timbren kits will either give you…

view full answer...

Answer 11

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 12

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Replacement Support Arm for 69 inch Flat Style Awning Support Arm

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching