Height of Tray On Kwikee RV Storage Slide Out Tray Assembly

Question

Question:

Hello, Can some one tell me the dimension of the extended portion of the Rail? See picture Thank you,

asked by: Stacy R

0

Expert Reply:

In regards to the Rail Kit for Kwikee RV Storage Slide Out Tray Assembly part # LC370793, the distance from the bottom to the top of the slide tray is 3-1/8" which you can see in the attached photo.

expert reply by: Conner L

0

Height of Tray On Kwikee RV Storage Slide Out Tray Assembly
(click to enlarge)

Answer 1

If your Mower does not have the Built-in Bracket then The Rack'em Grass Catcher for Toro, Bobcat, and Exmark Lawn Mower #RCMMS4-EXS1 will fit your Bobcat ZTR CRZ 48 inch Deck Riding Mower. If your Bobcat ZTR CRZ 48 inch Deck Riding Mower comes…

view full answer...

Answer 2

The Rack'em Grass Catcher for Bobcat Lawn Mower Deck with Built-in Bracket #RCMMS4-RS2 does fit your 2015 Bobcat Quick Cat standing mower. I checked out your mower and the location of where the discharge opening is matches what this is designed…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 10

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Height of Tray On Kwikee RV Storage Slide Out Tray Assembly

Product Page this Question was Asked From

Continue Researching