Bearing Kit for Trailer Hub that Has Seal 10-54 and Bearings 25580 and LM67048

Question

Question:

Current seal is a dexter 10-54 on a 5200lb axle. Inner bearing is 25580 outer is lm 67408. Non-EZ. Looking for the kit but can’t find the measurements for the 10-54 to match the gs-2250dl.

asked by: Ivan

1

Helpful Expert Reply:

The 10-54 Dexter seal is the same as the # GS-2250DL which has an inner diameter of 2.25 inch. Now if you were looking for a bearing kit that matches the bearings you have of 25580 and LM67048 the part # BK3-300 comes with everything.

expert reply by: Jameson C

1

Answer 1

The Grease Seals 10-36 (pair) #RG06-070 cross references as the fit for your 010-036-00 seal. This seal has an inner diameter of 2.250 inches and outer diameter of 3.376 inches. The Grease Seal - Double Lip - 2.250" ID - 3.376" OD…

view full answer...

Answer 2

Thanks for sending in the picture of your axle label. Based on that I know that the correct bearing kit is the #BK3-200 which comes with bearings and a seal for a 7k hub.

view full answer...

Answer 3

I recommend you remove your hub and current grease seal so you can determine what you currently have. There should be a number stamped on the outside of your grease seal. If not you will need to take an accurate measurement of the outside diameter of…

view full answer...

Answer 4

Thank you for the photo; I contacted Lippert with the information you gave me and they told me that you will need Grease Seal #GS-2250DL. This seal has a 2.250" inner diameter and 3.376" outer diameter; the seal you asked about, part…

view full answer...

Answer 5

If the bearing is brown or black then that is a sign that it has been overheated and will need to be replaced. You will also need to replace the race. Replace all these parts on both sides of the axle at the same time. Only certain races can be used…

view full answer...

Answer 6

For a Dexter 7k axle the correct grease seal is the part #GS-2250DL. Or for a kit that has the correct bearings and seal you'd want the part #BK3-200.

view full answer...

Answer 7

There are two common grease seals used on 7,000 lbs axles, part #GS-2250DL which has a 2.250" inner diameter and part #GS-2125DL which has a 2.125" inner diameter. The former is more common and used on newer trailers. They are both double…

view full answer...

Answer 8

If the outside and the inside of your tires are wearing out but the middle is not indicates that your tires are not inflated to the correct psi rating. Make sure you have your tires inflated to the correct psi by checking the sidewall of the tire. If…

view full answer...

Answer 9

The 6-Leaf Double-Eye Spring for 7,000-lb Trailer Axles - 24-7/8" Long #e64SR have a spring width of 1-3/4 inches. I've attached a video to assist with more dimensions for you.

view full answer...

Answer 10

Generally speaking you will want to have 3 inches from the top of your tire to the fender of your trailer when the suspension is fully compressed to accommodate for suspension travel. Having a little more wouldn't hurt, but I wouldn't…

view full answer...

Answer 11

What is more important then the amount of leaves that are on the spring is the weight capacity of the spring. The easiest way for you to determine which leaf spring has the correct capacity for your trailer would be for you to check the weight…

view full answer...

Answer 12

On a trailer axle there are a few measurements that you can take. Take a look at the picture I have included for reference. The "A" measurement is the hub face to hub face measurement. The hub face is the surface of the hub where the wheel…

view full answer...