Ultra-Fab Hitch Mounted Skid Wheels Height Dimension

Question

Question:

What is the distance from the mounting plate that is attached to the wheel, to the bottom of the wheel? Put another way, if the item were installed as specified to a 3X3 tube, how far below the 3X3 tube does the wheel extend? My trailer plug is welded to the hitch and extends downwards. So I am trying to ascertain whether mounting these rollers will clear the the trailer plug and prevent it from becoming the low point that scrapes the ground rather than the wheel. I already purchased the smaller version with the steel roller and only just realized that the roller does not extend below the trailer plug. I am lucky that I have not had cause to test these or else I would have lost my trailer plug connector!!

asked by: Colin M

0

Expert Reply:

The length from the bottom of the wheel to the top of the bracket on the Ultra-Fab Hitch Mounted Skid Wheels for RVs up to 30' Long - 4" Diameter - Qty 2 Item # UF48-979015 is 4-1/2".

expert reply by: Kevin C

0

UF Skid Wheel Dimension
(click to enlarge)

Answer 1

You're looking at 3-3/8" from the bottom of the wheel to the top of the mounting plate on the Ultra-Fab Hitch Mounted Steel Rollers for RVs w/ 2-1/2" Hitch Tubing #UF48-979017.

view full answer...

Answer 2

Thanks for reaching out, Michael! The Dexter Electric Trailer Brakes #K23-086-087-00 are compatible with 3,500 lb axles and have the standard 4-bolt pattern so if that matches the specs of your axle then this will definitely work for your…

view full answer...

Answer 3

Thank you for all of the info you gave. Based on that you'd want the trailer hub and drum part #AKHD-545-35-K that you referenced and then for brake assemblies to match you'd want the #AKEBRK-35-SA which is a self adjusting set for both sides…

view full answer...

Answer 4

I went out into our warehouse and pulled a set of the Ultra-Fab Rotating, Hitch Mounted Skid Wheels #UF48-979014 and found that the distance from the bottom of the wheel to where the bottom plate will be is 5-3/4 inches. Since the bumper you plan to…

view full answer...

Answer 5

I do have an option for you but the Curt Trailer Hitch Receiver part #13390 on your 2015 Subaru Legacy already has the highest ground clearance (10-1/4") of any other trailer hitch receiver we have confirmed to fit your vehicle. This measurement…

view full answer...

Answer 6

It sounds like you are looking for the OEM spare tire hoist for your 2015 Coachmen motorhome on a Chevrolet 4500 chassis. We do not have the OEM spare tire hoist and I am not aware of what part number they would be. We do have alternate aftermarket…

view full answer...

Answer 7

It is possible to mount the springs on top of the axle which is called "flipping the axle". To accomplish this we normally recommend an over-under conversion however there is not one with square u-bolts available for your square axle.…

view full answer...

Answer 8

Yes, there are SumoSprings that fit your 2021 Ford E-450 cutaway chassis, and what you need is the following: - SumoSprings Solo Custom Helper Springs - Rear Axle #SSR-130-54

view full answer...

Answer 9

The difference between the #SSR-106-47-1 and the #SSR-130-47 is the capacity. The #SSR-130-47 are light duty with a weight capacity of 1,500 lbs. Unless you're constantly hauling very heavy loads or towing heavy trailers these would be the best…

view full answer...

Answer 10

The SuperSprings Custom Suspension Stabilizer and Sway Control Kit #SSA22 is listed to fit and install above the leaf springs on your 2019 Coachmen Leprechaun 319MB. I tried looking up a photo of the suspension on your motorhome but I could find…

view full answer...

Ultra-Fab Hitch Mounted Skid Wheels Height Dimension

Product Page this Question was Asked From

Featured Help Information

Instructions

Miscellaneous Media

Continue Researching