EcoHitch Front Trailer Hitch Receiver For 2019 Chevrolet Silverado 3500 Bumper Trimming Location

Question

Question:

when it says BUMPER requires trimming, does this mean the plastic fascia or the steel bumper for 2019 Chevy 3500HD diesel? when something is ed into the hitch receiver, where do I temporarily locate the license plate so it can be seen? Also, will the relocated license plate require a light? Do you have any pictures of this hitch mounted on a 2019 Chevy 3500HD?

asked by: Tommy O

0

Expert Reply:

The EcoHitch Invisi Front Mount Trailer Hitch Receiver # 306-X7906 requires you to cutout part of the plastic portion behind the front license plate mount on your 2019 Chevrolet Silverado 3500. I have included a picture of the area that is included with the installation instructions. This area is only plastic but it can be multiple layers.

For the front license plate it will depend on where you will be operating your vehicle. If it is your only plate you can place it inside your front windshield or secure it to the front of what ever accessory that you are using. If you have front and rear plates some states only require one one plate on the rear of the vehicle so you would not need to concern yourself over the license plate in those states. Lighting is not required on a front license plate only the rear.

Currently we do not have any pics with this receiver installed on a 2019 Chevrolet Silverado 3500.

expert reply by: Bud M

0

Bumper Trimming Location
(click to enlarge)

Answer 1

The tow hooks on your 2015 Chevrolet Silverado 3500 do not need to be removed to install the Draw-Tite Front Mount Trailer Hitch Receiver part #65078. The bolts that hold the tow hooks do get removed but only to set the trailer hitch in place as…

view full answer...

Answer 2

The EcoHitch Invisi Front Mount Trailer Hitch Receiver part #306-X7906 is a great option for a 2019 Chevrolet Silverado 3500. The receiver tube is flush with the edge of the bumper so the hitch pin hole will be slightly recessed. This might make it…

view full answer...

Answer 3

Sounds like you are looking for a hitch mounted cargo carrier to mount in a front hitch for your truck. The most popular cargo carrier we have is the etrailer #e98874 which will fit a 2 inch hitch and can fold up when not needed. Being able to fold…

view full answer...

Answer 4

I do not have a completed installation photo nor did EcoHitch, but I can provide a photo showing where the receiver tube will sit in relation to the bumper. You'll need to make a hole in the fascia under the bumper directly behind where the front…

view full answer...

Answer 5

Excellent question, and you're right that bike racks experience tremendous bounce at the rear of a trailer, and it would require a specially-rated bike rack (of which there are few), so a front-mount hitch on your 2020 Chevy Silverado 2500 is a…

view full answer...

Answer 6

Normally trailer coupler height is around 17 inches, from the ground to the bottom of the coupler, and most hitch manufacturers design their hitches to work with a ball mount that will end up very close to this measurement. I am including a link to…

view full answer...

Answer 7

I confirmed with EcoHitch and their Trailer Hitch Receiver #EH39FR was just confirmed to fit your 2024 Tesla Model Y this week. This is great since the receiver opening is accessible through the rear cover plate just like a factory option.

view full answer...

Answer 8

To add a hitch to your 2024 Toyota RAV4 Prime, I recommend the etrailer item #e23ZR. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a 4,000 lbs towing capacity, and…

view full answer...

Answer 9

Yep, you're 100 percent correct. For your 2015 Chevy Silverado 2500, the correct EcoHitch front hitch is indeed the one you referenced, which is the following part number: - EcoHitch Invisi Front Mount Trailer Hitch Receiver #306-X7906

view full answer...

Answer 10

For your application I recommend using the EcoHitch Invisi Front Mount Trailer Hitch Receiver #306-X7906. This will fit in a cutout you make on the front bumper of your 2019 Chevy Silverado 2500 and it comes with a magnetic license plate mounting…

view full answer...

Answer 11

The EcoHitch Invisi Front Mount Trailer Hitch Receiver part #306-X7906 is the front mount trailer hitch I recommend for a 2019 Chevrolet Silverado 2500 because it is made in the USA and it installs inside the bumper so it won't hang down below…

view full answer...

Answer 12

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...