Does the Aluminum Modular Trailer Wheel - 16" x 7" Rim - 8 on 6-1/2 Have An Offset

Question

Question:

looking for a aluminum rim 16x7 8bolt pattern 4.5inch back spacing IS the LHJM513 Available with 4.5 backspacing

asked by: Larry N

0

Expert Reply:

The Aluminum Modular Trailer Wheel part # LHJM513 is a zero offset wheel which means the hub mounting face is centered in the wheel therefore, the backspacing is half of the wheel's width. This wheel is 7" wide so the backspacing is around 3.5" plus the lip. There are very few trailers wheels with offset, nearly all are 0.

Unfortunately, I don't think you'll be able to find a trailers wheel with 4.5" backspacing so you may want to consider alternative options.

expert reply by: Conner L

0

Answer 1

It took a little researching, but I was able to confirm the 7800026 is another number for #25580 and 7800017 is another number for #14125A. So with that being said, the Dexter #8327872 will definitely be a good replacement for your axle as…

view full answer...

Answer 2

I've never heard of an actual third brake light connector on a camper shell to plug in on a truck and we don't carry any parts to do that. The light generally needs to be hardwired into the truck's brake light circuit. The…

view full answer...

Answer 3

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on…

view full answer...

Answer 4

If you are installing just the Firestone Ride-Rite kit, #F2400, and not also adding an on-board air compressor such as #F2158, then I would estimate that it should take about 2 hours to install the kit. That is for someone with some mechanical…

view full answer...

Answer 5

Since you have a wheelbase/axle spacing of 38 inches the correct hanger kit for slipper springs would be the part #HAP-105-205-01. And then for a 7k trailer axle the u-bolt kit you'd want would be the part #APUBR-8. I attached the diagram to use…

view full answer...

Answer 6

If you are needing the hub and drum assembly then you will want to go with the Dexter Trailer Hub and Drum Assembly #8-201-5UC3-EZ but if you are just looking for an idler hub then you will want part #8-213-5UC1 instead. These come with the correct…

view full answer...

Answer 7

If your current springs have 5 leaves then going to a 7 leaf spring will increase the height of the trailer a little and make the trailer more susceptible to sway. Regarding capacity if you go with springs rated higher than what is required it will…

view full answer...

Answer 8

I have a solution for you, but we do not carry Glo-Brite lights, so replacing it with the same brand will not be something I can offer you. Instead, to replace your Glo-Brite 9852-88, I recommend using the Optronics LED Trailer Tail Light #STL72RB.…

view full answer...

Answer 9

If your vehicle has a factory brake controller plug, you can simply use the Tekonsha Plug-In Wiring Adapter for Electric Brake Controllers – Ford, Item #3034-P, which will connect to the vehicle plug and the brake controller. On the new E-450…

view full answer...

Answer 10

To see all of the correct wheel and tire combos you'd need check out the link I attached. The option I would recommend is the part #TA43RR which is a Load Range C tire size ST175/80R13 mounted on a white spoke wheel with a bolt pattern of 5 on…

view full answer...

Answer 11

To tow your trailer that uses an RV style 7-way blade style connector with your semi that has a 7-pin connector, you need to construct an adapter that will also combine the brake signal into the right and left directional signal pins. This can be…

view full answer...

Answer 12

What you're going to need is two of the transfer switches in that case. I have attached a diagram from Furrion that shows you how you're going to need to hook the two transfer switches #F30ATS up: -one to the other, then one branching off to…

view full answer...