Correct Hitch Ball for Anderson Ultimate 5th Wheel Hitch on Factory Gooseneck Hitch

Question

Question:

Which Gooseneck ball for 2020 GMC 3500 Denali with factory puck system that will fit my Andersen Ultimate hitch

asked by: Jerry L

0

Expert Reply:

In order to use the Anderson Ultimate 5th Wheel Hitch with a factory gooseneck hitch you'll simply need a standard height gooseneck hitch ball, the Curt Pop-In Ball part # C60601 is a standard height and works with Ford, Ram, and GM trucks.

expert reply by: Conner L

0

Answer 1

The RetraxPRO XR Hard Tonneau Cover - Retractable - Aluminum - Matte Black - Accessory T-Slots #RTT-80384 is the best retractable cover for your 2022 Ford F-350 Super Duty. The retractable design allows for full truck bed access in seconds. The…

view full answer...

Answer 2

We have a similar Pace Edwards retractable tonneau cover that can retract at 12 inch increments but the Switchblade part #PE66QJ can only be either all the way open or all the way closed. Instead you'd want the Full Metal Jacket part…

view full answer...

Answer 3

I went to the warehouse and took some measurements of the Curt Ball and Safety Chain Loops #C60618 for you. The outside to outside dimension of the loop is 4-1/4 inches. I have attached a photo of the loop with the dimensions shown you can check out.…

view full answer...

Answer 4

It sounds like you probably have the old Reese Classic 15k 5th wheel hitch, which is compatible with the #RP30048 slider base. This will allow you to convert your standard 5th wheel hitch to a sliding hitch.

view full answer...

Answer 5

The BAK Revolver X4s Hard Tonneau Cover, short bed #BAK99ZR or long bed #BAK49ZR, measures about 8" when rolled up. It doesn't roll up completely up to the front so it will probably hang over the bed about 9" or 10" so you'll…

view full answer...

Answer 6

The Andersen Ultimate Connection 5th Wheel Trailer Hitch System with Adapter - 20,000 lbs #AM3200 is designed to work with truck beds over 6' in length and has a gross towing weight of 20,000 lbs so your weight and bed length are covered. This…

view full answer...

Answer 7

If you're referring to the Andersen Ultimate 5th Wheel Hitch Connection you'd actually need to reach out to Andersen directly as we don't carry this. That said, Lippert, the trailer frame manufacturer for most new trailers on the road…

view full answer...

Answer 8

The BAK Revolver X2 Hard Tonneau Cover #BAK39602 referenced in your question will need to be fully open, up to the truck's cab, or fully closed down at the tailgate in order for it to be secured by the built-in straps and buckles. It can…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

Yes, you can replace your current Lippert Equa-Flex equalizers with the MORryde AllTrek 4000 Equalizers #MR29DR on your 2018 Highland Open Range. The yellow octagons on the front and rear are a for correcting the alignment of the axles and are not…

view full answer...

Correct Hitch Ball for Anderson Ultimate 5th Wheel Hitch on Factory Gooseneck Hitch

Product Page this Question was Asked From

Continue Researching