Hole Size Needed For A Thumb Turn Cam Latch Cylinder

Question

Question:

How big of hole will this need?

asked by: Jeff K

1

Helpful Expert Reply:

The Replacement Thumb Turn Cam Latch Cylinder - Stainless Steel - 1-1/8" Long Item # 295-000012 will require a 3/4" hole to install.

expert reply by: Kevin C

1

Answer 1

If you are only wanting to replace the cylinder you need the Replacement Thumb Turn Cam Latch Cylinder - Stainless Steel - 1-1/8" Long Item #295-000012. If you are wanting to replace the whole latch you need the replacement thumb latch you need…

view full answer...

Answer 2

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 3

The number you provided, "7753400" is a patent number which corelates to the Equalizer for E-Z Flex Suspension part #013-144-03. This is for a single equalizer but if you need the entire kit it's the Dexter E-Z Flex Suspension Kit part…

view full answer...

Answer 4

The only way you could power interior dome lights on a trailer without it being connected to a tow vehicle would be to power the lights with a battery like a breakaway battery. How you choose to wire up the batteries will in the end be up to you, but…

view full answer...

Answer 5

For your enclosed trailer application I have several suggestions for adding interior lighting that you can control directly via a switch. Since your current 4-pole trailer wiring does NOT include a 12V auxiliary power feed that could power inside…

view full answer...

Answer 6

I would be happy to help you set up your 2022 Toyota Highlander to haul your new travel trailer. The wiring harness you currently have controls your trailer's lighting functions only. You do not need to rewire your Toyota you just need another…

view full answer...

Answer 7

I would love to help you upgrade the suspension on your Twilight 2800 travel trailer. The MORryde Rubber Equalizers for Tandem Axle Trailers #MR87ZR that you referenced are a great solution but we do need to double check a few things. First is that…

view full answer...

Answer 8

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 9

It's totally normal for a bit of movement between any fifth wheel hitch and the base rails. The feet on the hitch are typically a bit smaller than the slots they slide into for mounting otherwise you'd have a hard time getting your hitch in…

view full answer...

Answer 10

Since Demco uses 3,500 drum brake assemblies part #DMSB24429M and #DMSB24428M what you'd need is similar 3,500 electric brake assemblies like the etrailer part #AKEBRK-35L-SA for the left hand side and #AKEBRK-35R-SA for the right hand side. To…

view full answer...

Answer 11

Unfortunately there are no plug-in adapters or harnesses that would allow you to replace the factory 4-way flat trailer connector with a 7-way or a 7-way and 4-way connector on your 2005 Ford F-150. To complete the installation for a brake controller…

view full answer...

Answer 12

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...