Will the Trailer Valet Trailer Wheel Dolly Set Work On a Single Axle Trailer

Question

Question:

I have a single axle 20 foot Airstream that I want to fit in a tight spot. I need a set of castor dollies to be able to move it sideways and diagonally. Does that exist?

asked by: Bill S

0

Expert Reply:

The Trailer Valet Trailer Wheel Dolly for Tandem Axle Trailers part # TV74FR can be used on a single axle trailer if the weight of the trailer is under the 7,000 lb weight capacity of the dolly. It will do a great job of helping maneuver the trailer front to back or side to side.

expert reply by: Conner L

0

Answer 1

We have a great trailer dolly for you. It's the Trailer Valet 5X Swivel Jack and Trailer Mover, part #STC-V211. This dolly can handle trailers with a gross weight of 5000 pounds and tongue weights up to 500 pounds. It works by turning a crank…

view full answer...

Answer 2

Thanks for reaching out! The purpose of the Trailer Valet Trailer Wheel Dolly for Tandem Axle Trailers #TV56FR is to give you better maneuverability with a tandem axle trailer when utilizing a trailer dolly like the Trailer Valet XL #TVXL25. The…

view full answer...

Answer 3

Trailer Valet XL Trailer Dolly #TVXL25 will be able to move your trailer at the near 90 degree angle and up the incline of the driveway. The dolly has 2 gears and you will likely find that the low speed, 27 to 1 ratio will make it easier on you…

view full answer...

Answer 4

The best recommendation I can make would be to have the trailer attached to a tow vehicle so that the jack can be unsupported and you can easily access it. After that you'll need to unbolt the wheel assembly from the jack. Remove the valve stem…

view full answer...

Answer 5

The Trailer Valet XL Trailer Dolly with Chain Drive - 2" Hitch Ball - 10,000 lbs item #TVXL2 has a 1,000 lbs tongue weight capacity. This should easily accommodate your boat trailer on a flat surface and over a slight incline. The Trailer Valet…

view full answer...

Answer 6

Yes, you can switch from the 2-5/16" hitch ball to a 2" hitch ball with the Trailer Valet XL Trailer Dolly with Chain Drive - 2-5/16" Hitch Ball - 10,000 lbs #TVXL25. All you will need is the 2" Hitch Ball w/ Base for Trailer…

view full answer...

Answer 7

As long as the tongue weight of the trailer is around 10-15 percent of the total trailer weight the Trailer Valet XL Trailer Dolly #TVXL25 is going to work like it was designed for. It does decently on flat surfaces and inclines but if it's an…

view full answer...

Answer 8

Was the ball starting to pivot in the coupler? Did you have the latch of the coupler completely latched down and then have the collar tightened totally to the bottom of the coupler? If you did this it SHOULD work fine and not tilt like you mentioned.…

view full answer...

Answer 9

It sounds like your military trailer uses a pintle style coupler such as #C48200. Trailer Valet does not offer an adapter for using this type of trailer with their XL Trailer Dolly #TVXL25. The main reason is that military surplus trailers will tend…

view full answer...

Answer 10

The Trailer Valet XL Trailer Dolly with Chain Drive - 2-5/16" Hitch Ball - 1,000 lbs TW #TVXL25 or the 2 inch ball #TVXL2 have two different drive gears to make it easier to go up an incline or to overcome a lip in the concrete as you described.…

view full answer...

Answer 11

The weight of the Trailer Valet XL #TVXL25 that you referenced is 60 lb. This has a 1,000 lb tongue weight capacity and 10,000 lb total trailer weight capacity.

view full answer...

Answer 12

I wish there was a way to free wheel the Trailer Valet. The only way to do that would be to install a second jack on the trailer that has a wheel caster on it which you could lower when you needed the ability to free wheel. Something like the Fulton…

view full answer...

Will the Trailer Valet Trailer Wheel Dolly Set Work On a Single Axle Trailer

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching