How To Confirm Fit of Kodiak Disc Brake Kit

Question

Question:

Hello my boat trailer currently has drum brakes T1544500042 would I be able to switch to this disc brake set and not have any problems? I just get the bearings listed to fit this and it would work?

asked by: Rob M

0

Expert Reply:

The Kodiak Disc Brake Kit part # K2HR2D is designed for 2,000 lb axles which use L44649 bearings. Therefore, so long as these are the bearings your axle uses, you have a four bolt mounting flange, and wheels between 10-13" then it will fit.

expert reply by: Conner L

0

Answer 1

We do have one kit that may fit your 2200lb axle, but you will need to confirm which bearing combination it uses, and you will need to replace the wheels with 13" wheel as it is not compatible with your 14" wheels. You can do this by…

view full answer...

Answer 2

There are a few additional factors to consider other than the wheel size before determining if the Kodiak Disc Brake Kit, #K2HR2D, will fit on your trailer. According to Kodiak, this kit was designed to fit 10 inch to 13 inch wheels, so they will…

view full answer...

Answer 3

If you install the Kodiak Disc Brake Kit #K2HR2D with the included bolt on mounting flange you would not have to worry about the piston not fitting with the bracket. I attached a picture that shows the backside of the caliper and you can see that the…

view full answer...

Answer 4

The 7290 that you see is a casting number. It is found on AL-KO hubs that fit #99 spindles. I found that the bearings used are #28580 which would be the inner bearing and #25580 which would be the outer bearing. For the seal use #91030.

view full answer...

Answer 5

The Tow Ready wiring harness #118571 is rated for 7.5 amps for brake lights and turn signals and 7.5 amps total for running lights. The fuse that goes on the power wire connection to the battery is a 10 amp fuse. The wire gauge of the long 12 volt…

view full answer...

Answer 6

For the LCI52-SB-86.5-68.5, the two ending measurements are: 1st - measurement from hub to hub, meaning the length of the axle in this case is 86.5 inches. 2nd - spring seat dimension where they're welded, meaning the spring seats are 68.5 inches…

view full answer...

Answer 7

Actually our etrailer.com brand brake assemblies are rebranded AxleTek assemblies. So we have the 8k left and right assembly set #AKEBRK-8 which is most likely what you need but these are 12-1/4 inch in diameter by 3-3/8 inches wide and attach with a…

view full answer...

Answer 8

I have a solution for you Travis as Pace Edwards does not offer a contractor rack for your 2023 GMC Sierra 1500. Instead you can use the Pace Edwards Full-Metal JackRabbit Retractable Hard Tonneau Cover #311-M-FMCA28A59 with the Thule TracRac SR…

view full answer...

Answer 9

It could be a tow package fuse on the vehicle. Use the owners manual to find the locations of fuses/relays related to the tow package wiring to check them and replace as needed. If the issue is not a fuse or relay then you can test the vehicle side…

view full answer...

Answer 10

Since the issue appears to be on the vehicle side for your 2017 Toyota Tacoma, I recommend first checking the connector itself. Look to see if there is any dirt or corrosion built up inside the connector that may preventing a solid connection with…

view full answer...

Answer 11

I spoke to my contact at Horizon Global. He said it is acceptable to mount the Bulldog Powered-Drive Kit #BD1824200100 to the slave jack itself. He also said that if you need to switch the motor wires to make it work correctly, that would be fine, as…

view full answer...

Answer 12

You will need the Red LED Trailer Clearance or Side Marker Light #328-K-52 or Amber LED Trailer Clearance or Side Marker Light #328-K-51 for your 2018 Forest River Sunseeker motorhome. These lenses have the same Top Command SAE-AP2-16 markings on the…

view full answer...

How To Confirm Fit of Kodiak Disc Brake Kit

Product Page this Question was Asked From

Featured Help Information

Instructions

Continue Researching