Which Replacement Key for Rhino Rack Roof Rack with Lock Core 005

Question

Question:

Rhino sport Rack on my camper roof its say 005 on the female key lock. on the will your SR005racork

asked by: Dsvid H

0

Expert Reply:

I have a solution for you, but the SportRack # SR005 will not work on RhinoRack lock cores. Instead you'll need the Rhino-Rack Masterkey Lock Barrels - Keyed Alike - Qty 2 # RRRK005-2, which is the replacement keys you need with extra keyed alike lock cores. The keys are not available without the lock, so this would be the only solution available.

expert reply by: Erik B

0

Answer 1

For your Rhino-Rack, you can use the Rhino-Rack Masterkey Lock Barrels #RRRk059-2. This kit comes with two locking cores, and two replacement 059 keys. The keys are not available separately, unfortunately.

view full answer...

Answer 2

If you install any roof rack on your 2012 Mazda 3, you can remove it if needed, even if that rack attaches to the fixed points on the vehicle. The fixed points for the rack are located under small plates that you can just pull up and off of the…

view full answer...

Answer 3

The lock core number isn't stamped on the outside of the core so if the rack is locked you will need to get a locksmith to unlock the core and then use a change key like #853-1251 to remove the core. If the lock is unlocked then you will only…

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 7

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 8

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 9

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 10

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 11

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 12

The three most common lug stud sizes for a trailer are 1/2"-20, 9/16"-18, and 5/8"-18. In order to make sure you get the correct lug nuts you need to measure the lug studs on the trailer now as we have no way to look this up for…

view full answer...

Which Replacement Key for Rhino Rack Roof Rack with Lock Core 005

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching