Which Pullrite Capture Plate to Use with Lippert 1621 Pin Box

Question

Question:

please provide dimensions for this part so i can determine the correct capture plate for my Pullrite hitch, thanks.

asked by: Janes R

0

Expert Reply:

The Lippert pin box part # LC1387882 that you referenced is a standard Lippert 1621 so the Pullrite capture plate you'd need is the # 331704 which you'd have to get from Pullrite.

expert reply by: Jameson C

0

Answer 1

Mainly the difference is the Lippert 1116 is considered a medium length pin box and the 1621 is considered a long one. It's not by much but the 1621 stick out about 3 inches further.

view full answer...

Answer 2

Pin box bolt torque is based on the size of the bolts. 1/2 inch Bolts GR5 90 ft-lbs 5/8 inch Bolts GR5 150 ft-lbs 3/4 inch Bolts GR5 275 ft-lbs

view full answer...

Answer 3

I went to our warehouse and measured the holes you mentioned you wanted the measurement for on the Lippert 1621 5th Wheel Pin Box, part #LC1387882. The holes measure 3/8 inch diameter. I have also attached a drawing of this pin box with the…

view full answer...

Answer 4

Lippert 1621 5th Wheel Pin Box - 15,500 lbs Item #LC1191191 weighs approximately 100 pounds including the wings the pin box bolts to. Lippert 1621 5th Wheel Pin Box - 21,000 lbs Item #LC1387882 weighs approximately 115 pounds including the wings the…

view full answer...

Answer 5

When a 5th wheel hitch's height is raised to increase clearance between the bottom of the trailer overhang and the tops of the truck's bed rails this can put the trailer into a nose-high orientation. Since trailers tow best when they are…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 8

I spoke with my contact at Trailair and from your serial number we were able to determine that your trailer came with a 1621 HD pin box which is a long pin box style. I was unable to obtain the exact part number for your Trailair pin box but from the…

view full answer...

Answer 9

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 10

Hey Jay. It sounds like you are on the right track here because a sidewinder pin box will be your only option for pulling your 5th wheel since you have a short bed truck with the Rambox. That said, you are right that the Reese Sidewinder cannot be…

view full answer...

Answer 11

If you take a look at the linked diagram you can see the minimum recommended clearance distances between truck and trailer for 5th wheel towing. It is recommended to have at least 5-inches from the top of the bed rails to the bottom of the trailer…

view full answer...

Answer 12

There should be a sticker or plate on the pin box itself that lists the manufacturer and model of the pin box. If it is not present then there are some measurements you can take to determine the model of the pin box. I have included a link that…

view full answer...

Which Pullrite Capture Plate to Use with Lippert 1621 Pin Box

Product Page this Question was Asked From

Continue Researching