Replacement 12 inch and 8 inch Keel Rollers for Boat Trailer

Question

Question:

Hi - we have a galvanized trailer with 4 rollers 1 12inch roller rear and 3 8inch rollers moving forward from the rear. The holders for the rollers are in great shar and galvanized so, wed just need the replacement pins and rollers. The trailer is primarily used in saltwater rinsed with fresh water after each use and wed like to replace the rollers with something that will hold up. Our boat is a 24foot Limestone 24 deep V. Which rollers and pins would you recommend? Thanks

asked by: Norm L

0

Expert Reply:

For the 12 inch roller you'd want the part # CE29519 which is made from a very durable PVC that is non-marking. For pins and a shaft you'd just need the part # CE10727A.

Then for an 8 inch setup that comes with the mount as well you'd want the part # CE10453G and you'd be set.

expert reply by: Jameson C

0

Answer 1

I don't have a wiring diagram, but I'd be happy to explain it for you. In order for the reverse solenoid on a Hydraulic Brake Coupler like #DM62VR to function, one of the two wires leading from it needs to be connected to the wire…

view full answer...

Answer 2

Most keel rollers for boat trailers like the CE Smith Keel Roller for Boat Trailers part #CE29519 or CE Smith Keel Roller for Boat Trailers - Self Centering part #CE29505 don't have listed weight capacities as they aren't supporting…

view full answer...

Answer 3

I recommend the Tourney Pro Transom Saver #315-FXJ for your 5'x8' plastic boat. The transom saver is definitely recommended with the lightweight plastic boat you have. With this transom saver you can mount it to the trailer by sliding…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 6

The manual lockout on your Atwood 85778 surge brake coupler is there so that you can back up the trailer without the brakes locking up on you. Yes you can safely tow your trailer with the broken manual lockout, you just have to make sure you…

view full answer...

Answer 7

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 8

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 9

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the '90s.…

view full answer...

Answer 10

Traditionally, trailer manufacturers did not use electric brakes on boat trailers because the brake magnet wiring and trailer wiring did not always have the best insulation or water protection. These days, more and more manufacturers are using…

view full answer...

Answer 11

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement 12 inch and 8 inch Keel Rollers for Boat Trailer

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching