4-1/4 Diameter LED Interior RV Light Replacement

Question

Question:

The spring mount led light you show is 3 1/8 in diameter and the one I have to replace in my camper measures 4 1/4 inch in diameter. Do you carry this larger size? I am having trouble finding a replacement

asked by: Shirley L

0

Expert Reply:

The Glantastic LED RV Puck Light - 197 Lumens - Semi-Recessed - Frosted Plastic Lens - Warm white Item # 328-K-58L34P9 is the 4-1/4" diameter you're needing. This is mounted a little differently as you'll have to screw it into the ceiling instead of using spring mounts.

expert reply by: Kevin C

0

Answer 1

I spoke with my contact at Lippert and he informed me that the lights flashing indicate the low point of the coach and that if you perform a zero point calibration you will correct that. In the service manual you will need to follow the…

view full answer...

Answer 2

We have the low profile, semi-recessed Glantastic LED RV Puck Light, #328-K-58L34P9. You do not mention what the dimensions are on your current Jupiter lights, I searched online and from what I was able to find think they may be a similar…

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You have a good eye as the black tubing sections are plastic for the Camco Gen-Turi RV Generator Exhaust System #CAM44461. It's just the curved pipe section that is made out of stainless steel.

view full answer...

Answer 9

Class I and Class II hitches both have a 1-1/4 inch receiver opening. The difference is that a Class I hitch has a lower tongue weight rating, usually 200 pounds and a lower towing rating, usually 2,000 pounds. A Class II hitch usually has a tongue…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

For sag from towing a trailer the best recommendation I can make is actually a weight distribution system. Suspension enhancement will help level your truck while towing. But the advantage to a weight distribution system is that it levels the vehicle…

view full answer...

Answer 12

If you just need a 4-pin to 7-pin trailer wiring adapter, then you can use part #C57672. This will plug into the 4-pin trailer connector on your brother's vehicle and give him the 7-pin socket for the trailer. Keep in mind, this will only give…

view full answer...

4-1/4 Diameter LED Interior RV Light Replacement

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching