Murphy Bed Mattress Replacement

Question

Question:

Looking to replace ours

asked by: Cesar

0

Expert Reply:

The etrailer eDream RV Mattress - Innerspring - 75" Long x 60" Wide - Short Queen Item # e94FR will be a great replacement for your Murphy Bed mattress as long its dimensions are 75"L x 60"W. If not please email back with the dimensions and I can recommend the correct fit for your needs.

expert reply by: Kevin C

0

Answer 1

The etrailer eDream RV Mattress #e94FR that you mentioned does not fold in half, however these mattresses are pliable and will work just fine in a Murphy bed. Murphy bed's typically are designed to accommodate mattresses that are up to 12"…

view full answer...

Answer 2

The etrailer eDream RV Mattress part #e94FR is pliable enough that it can be folded, so yes this would work great in a murphy bed setup.

view full answer...

Answer 3

Most Murphy beds are designed for mattresses that are 12 inches thick. Since the etrailer mattress #e97FR is 14 inches thick it most likely would be too thick. We have the part #DE36ZR which is 9 inches thick and the part #E84FR that is 13 inches…

view full answer...

Answer 4

We have the exact mattress you are looking for with one that is 75 inches long x 60 inches wide, the etrailer eDream Supreme RV Mattress #e97FR. This mattress has both a soft memory-foam side and a firmer side so you can choose which is the right fit…

view full answer...

Answer 5

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 6

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 7

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 8

You are correct that this refrigerator does not have an ON/OFF switch or function. The best you can do is "Standby" that draws an unknown amount of power. One option is to pull the 12-Volt fuse at the RV power center. A much better option…

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

From what I could find it looks like your 122R (red) and 122Y (amber) lights measure 3.75" x 1.70" x .81". We don't have any replacement lense directly for the GLO-BRITE lights but we do have some similar lights that you could use…

view full answer...

Answer 11

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 12

The Dometic RV Water Heater - Gas - Automatic Pilot - 12 Volt - 8,800 Btu - 6 Gal Tank Item AT96121 is the direct replacement for the GC6AA-10E. Unfortunately it is out of stock with no expected restock date. Instead I recommend the Furrion RV…

view full answer...

Murphy Bed Mattress Replacement

Product Page this Question was Asked From

Continue Researching