Connector Solution for Connecting Maxxair Temporarily to Generator

Question

Question:

I just bought a maxxair fan from you. I am planning on powering it with my goal zero Yeti 1000. I understand that it is a 12 volt fan. What is the best connector to use to plug it in to the goal zero? Can I use a regular two prong plug or do I need to use the cigarette or Anderson connectors to power it? I have a two wire household plug I could use. Do you have other two wire connectors if the household plug won’t work? Thanks,

asked by: Gary

0

Expert Reply:

Basically any wiring connectors are going to work and it would be your preference. You could use the part # RM-9331 on either side of the wiring for an easy cigarette lighter style connector setup.

expert reply by: Jameson C

0

Answer 1

You should be just fine replacing your two roof vents with the Fan-Tastic Vent Roof Vent #FV803350 since these fit the standard 14-1/4 x 14-1/4-inch RV roof opening size. Since you are replacing two 12V powered vents with two similar units your…

view full answer...

Answer 2

For a 10 gallon Atwood water heater like what you have the correct replacement anode rod is the part #CAM11593. The water heater does not need to come out either as it would be accessible from the outside of the RV.

view full answer...

Answer 3

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 4

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 5

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

As far as wiring for the 2024 Toyota Grand Highlander, we do have the Curt #C59236 available which is more of a universal hardwire harness. Unfortunately there are not any plug-and-play options that have been confirmed to fit as of yet (October 4,…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, we do. To add a hitch to your 2024 Toyota Grand Highlander, I recommend the Curt Trailer Hitch item #C26VV. This hitch is custom fit and bolts to your Toyota with included hardware. This is a class III hitch with a 2" receiver. It has a…

view full answer...

Answer 10

I did some checking and the hub/drum we offer that will work for you is the part #8-430-5UC3. This uses the same bearings as the 8-415 and will be an exact fit aside from the fact this is a non-ABS setup and the 8-415 came in an ABS setup and non-ABS…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

To replace your NOK AD2527E seal you can use #168233. It has an inner diameter of 1.688 inches and an outer diameter of 2.332 inches. Based on what I could find on the NOK AD2527E the inner diameter is the same and the outer diameter is 2.328 inches.…

view full answer...

Connector Solution for Connecting Maxxair Temporarily to Generator

Products Referenced in This Question

Continue Researching