Which Grease Seal For Dexter 3500lb Idler Hub 008-256-07?
Question:
I am about to do some rebuilding of a Jamar trailer and would like to know what grease seals are needed for wheel hub # 8-256-07. Thanks
asked by: Steven R
Expert Reply:
The Dexter 3500lb Idler Hub 008-256-07 you have on your Jamar Trailer uses grease seal # RG06-050.
If you need bearings as well you can use Bearing Kit # BK2-100 which includes inner bearing # L68149, outer bearing # L44649, races, grease seal # RG06-050, and a new cotter pin and tang washer.
I included videos of the products mentioned for you to take a look at .
Products Referenced in This Question
Hub Bearing Kit for Lippert, Dexter, and AL-KO Axles - 3,500 lb with #84 Spindle
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- Bearing Kits
- Bearing L44649 and L68149
- Race L68111 and L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L44649
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.063 Inch I.D.
- Bearing L44649
- Race L44610
- 3500 lbs Axle
- etrailer
more information >
Replacement Trailer Hub Bearing - L68149
- Trailer Bearings Races Seals Caps
- Bearings
- Standard Bearings
- 1.378 Inch I.D.
- Bearing L68149
- Race L68111
- 3500 lbs Axle
- etrailer
more information >
Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Trailer Bearings Races Seals Caps
- Seals
- Grease Seals - Double Lip
- 1.719 Inch I.D.
- 2.565 Inch O.D.
- etrailer
more information >
Product Page this Question was Asked From
Trailer Idler Hub Assembly for 3,500-lb Axles - 5 on 5 - Pre-Greased
- Trailer Hubs and Drums
- Hub
- Pre-Greased
- Standard
- L68149
- L44649
- For 3500 lbs Axles
- 1/2 Inch Stud
- 5 on 5 Inch
- 13 Inch Wheel
- 14 Inch Wheel
- 14-1/2 Inch Wheel
- 15 Inch Wheel
- etrailer
more information >
Featured Help Information
Miscellaneous Media
Continue Researching
- Shop: Grease Seal - Double Lip - ID 1.719" / OD 2.565" - for 3,500-lb Axles - Qty 2
- Article: How to Measure Your Trailer Wheel Bolt Pattern
- Q&A: How to Determine if Trailer has 84 Spindle to Pick Out Replacement
- Article: How to Tell the Weight Rating of a Trailer Axle
- Q&A: Availability Of Trailer Idler Hub With 5 on 5 Bolt Pattern
- Q&A: Replacement Hub for Utility Trailer with Dexter 8-256 Hub
- Q&A: What is the Difference Between Load Range C and D ST175/80D13 Trailer Tires
- Q&A: Is 16 Gauge Wire Adequate for Trailer Wiring for Lighting
- Q&A: Which Holds Up Better on Trailer Wheel Powder Coat or Acrylic Paint
- Q&A: How to Install Ground Wire To Trailer Connector on Utility Trailer
- Article: Most Popular Wheel Bearings
- Article: Trailer Maintenance Schedule
- Article: Trailer Tire Sizing
- Article: 7 Common Questions Everyone Has About Trailer Tires
- Article: Replacing the Bearing, Races and Seals on a Trailer Hub