MS5006WR Jensen Speaker Measurements

Question

Question:

I am looking to replace my RV speakers and looking at the speaker above. I am concerned about your stated bolt hole spacing at 3+ inches when the speaker requires a larger hole? What is the bolt hole circle DIA?

asked by: Tim M

0

Expert Reply:

I pulled this speaker from inventory to take a picture and measurements. The diameter at the outside edge of the grill is 5-9/16". The mounting hole diameter is 4-7/16" The center of the screw holes are inset 1/4", so the diameter measured at the screw hole centers is 5-3/8". I have attached a dimensioned picture of these measurements.

expert reply by: Les D

0

Jensen MS5006WR Speaker Mounting Measurement
(click to enlarge)

Answer 1

The Jensen Marine Speakers #MS5006WR has an edge to edge diameter (including the grill) of 6" and the mounting hole center to center distance is 3-3/4". If you're wanting to reuse the old mounting holes then you would want the Jensen…

view full answer...

Answer 2

For speakers that work well with the Jensen Stereo with Bluetooth, Item #JWM60A, I recommend the Jensen RV Speakers with Grilles, Item #HDS3000. These 60 Watt, 5 inch durable speakers mount within your RV and can be mounted outside as well. If you…

view full answer...

Answer 3

Both the Jensen JWM6A and the current model, part #JWM62A are classified as double-DIN head units, which will both use the same sized rough openings in a vehicle dash. The old #JWM6A and the current model #JWM62A both use the same pigtail, as you can…

view full answer...

Answer 4

The Jensen RV Stereo part #JWM60A would work well in the opening size you mentioned. I attached a picture of it's dimensions so that you can tell it was made to fit same size opening. This also can play CDs, DVDs, USB drives, and has Bluetooth…

view full answer...

Answer 5

The screw holes for the Jensen Marine Speakers #MS5006BR are 3-3/4" from side to side or top to bottom and 5-1/2" diagonally.

view full answer...

Answer 6

The RV Propane Gas Detector part #RS64FR is what I recommend using to replace the the Atwood RV Propane Gas Detector part 31013 (Discontinued). The mounting plate for this new detector will cover up any holes you had for the previous so it will be a…

view full answer...

Answer 7

You can use the RV Propane Gas Detector #RS64FR to replace your current Atwood 31013 propane gas detector. This will also use a 12v, 2-wire installation like your current detector.

view full answer...

Answer 8

The Go Power Solar Cable Entry Plate #34273840 is designed to connect to MC4 cable connectors like the part #34276216 and because of that doesn't have a max gauge. The #34276216 I referenced is 10 gauge but if you have 6 gauge wire with MC4…

view full answer...

Answer 9

I may have a solution for you, but the only way to boost your cellular signal would be through your carrier and in a lot of instances if the area you're camping doesn't generally have good service, a booster isn't going to do much. With…

view full answer...

Answer 10

Yes, it's very common that most campsites only offer 30 amp service and you would not have an issue still using your SurgeMinder Surge Protector and Circuit Tester - 50 Amps #SU99SR to protect the trailer along with an adapter to connect to the…

view full answer...

Answer 11

Yes, the Bluetooth Dongle for Rockford Fosgate Hide-Away Receiver #292-101461 is compatible with your Rockford Fosgate RFX4000 hide away receiver. This adapter plugs into the back of the receiver and will provide Bluetooth capability.

view full answer...

Answer 12

I reached out to my contact at Jensen and he did say that your AWM975 model stereo has been out of production for a while. To replace the unit he said the best option is with the Jensen RV Stereo #JWM60A, which features the same cutout size and…

view full answer...

MS5006WR Jensen Speaker Measurements

Product Page this Question was Asked From

Continue Researching