Replacement Extang Tarp for Part Number 44650 of 2011 Chevy Silverado

Question

Question:

Hi. I found the number written on the original canvass on my Trifecta bed cover and need a replacement canvass. Vehicle: 2011 Silverado 6.5 foot bed w/o cargo management system. Existing canvass: Model: 44650 Mfg date: 4/27/13 Can you tell me which replacement canvass to order? Thank you.

asked by: Steve B

1

Helpful Expert Reply:

Thanks for the part numbers you found on your Extang tonneau. Based on that the correct tarp would be the part # EX92645-20.

expert reply by: Jameson C

1

Answer 1

The correct replacement tarp for your Extang Trifecta 44650 is the part #EX92645-20.

view full answer...

Answer 2

Extang no longer produces the Replacement Tarp 43650B for the Trifecta Soft Tonneau Cover 44650. The Extang Trifecta 2.0 Soft Tonneau Cover #EX92650 replaces the 44650 tonneau you currently have. They do offer a Replacement Tarp #EX92650-20 for the…

view full answer...

Answer 3

We do have the Replacement Tarp #EX92645-20 which fits the Extang Trifecta 2.0 Soft Tonneau Cover #EX92645 for your 2010 Chevrolet Silverado with the 5'8" bed.

view full answer...

Answer 4

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 5

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 6

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 7

The OEM prep package consists of 4 "pucks" in the bed of the truck that will allow you to drop in puck style hitches for easy installation and removal, that gives you a completely clear bed when not in use. The B&W Companion OEM 5th…

view full answer...

Answer 8

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Answer 9

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 10

Choosing the right height setting for your 5th wheel hitch is a combination of a few different variables. First of all you want your towing setup to be as level as possible. With your Montana High Country 340BH level you will want to measure from the…

view full answer...

Answer 11

Lance does have a proprietary plug, but many customers see a standard 6-way or 7-way round and notice it doesn't fit their factory 7-way as well. I've attached an article to help if you have one of the 7-way or 6-way round connectors which we…

view full answer...

Answer 12

Although both the #LM67048 and the #14125A bearings might have the same inner diameter of 1.25 inches, they aren't interchangeable. Both bearings are compatible with a different race or bearing cone. The races have a different outside diameter,…

view full answer...

Replacement Extang Tarp for Part Number 44650 of 2011 Chevy Silverado

Product Page this Question was Asked From

Continue Researching