Replacement Bearings L68149 and LM67048

Question

Question:

I just packed the bearings on my camper. It has bearings L68149 and M67048. I can not find this combination on your web site. Is L44649 an updated number for the 67048 bearing. It has a 6 lug drum on it. I will need 4 sets when I purchase them for all 4 wheels. The seal is Dexter 010-019-00.

asked by: Gary C

1

Helpful Expert Reply:

Since we don't have a kit that has the bearing numbers you mentioned you'd need to order the bearings individually like with part # L68149 and # LM67048, and then for a seal part # RG06-050 and you'd be set.

The other number you mentioned is not a carry over replacement for what you have so it would not work.

expert reply by: Jameson C

1

Answer 1

We can help you check to see if you can install new hubs that have a different wheel bolt pattern. The key is knowing your current hubs' bearings, both inner and outer. A new hub can be installed so long as it uses the same bearings as the…

view full answer...

Answer 2

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 3

To determine the size of the hub assembly you need to purchase you have to determine which bearings are in the old assembly. If the old assembly has L44649 inner bearings, you would use the hub you chose #8-258-5UC1. If the inner bearings are marked…

view full answer...

Answer 4

Hey David, from previous customers of ours who have the same 2020 Keystone Raptor 424 we have determined that your pin box style is the Lippert 1621 which means for a Gen-Y gooseneck adapter you'd want the #GY58GR that you referenced.

view full answer...

Answer 5

Even though I cannot comment specifically on the grease you used because I am not familiar with it, I can tell you the best grease for trailer bearings is a a grease with a rating of GC-LB, which just means it is made to withstand very high…

view full answer...

Answer 6

A BT8 spindle would have a diameter of .99 of an inch where the bearings would both install and would have a diameter of 1.24 where the great seal would ride. That would require a hub part #AKIHUB-440-2-1K for an idler hub. A BTR spindle would have…

view full answer...

Answer 7

To determine the size of the brake assemblies you need you have to measure the depth and width of the hub drum on the axle like what you see in the picture I attached. The most common size is 2-1/4 inch wide like the #T4071600-500 that you…

view full answer...

Answer 8

To find the load capacity for your axle you should look on the trailer VIN plate or sticker that lists the VIN number. The weight rating of the axle should be listed on that same plate or sticker. Also, the axle could have a tag or plate on it that…

view full answer...

Answer 9

Based on the GVWR of your 2019 Jayco North Point 315RLTS it does seem like you have 7k axles. I recommend verifying this information to be sure. These axles typically use the #14125A outer and #25580 inner bearing found in the Timken #TMK92VR.…

view full answer...

Answer 10

You can verify that the 10-19 grease seal included in Bearing Kit #BK2-100 is the correct one for your spindles by taking two measurements. First you want to measure the rear hub bore where the seal is inserted. The seal's outer diameter needs to…

view full answer...

Answer 11

The inner diameters of the LM67048 and 15123 both are the same (1.250 inches). That means that a hub with either bearing in the outer bearing would fit your spindle. The part #AKHD-655-6-EZ-K would fit your axle.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Replacement Bearings L68149 and LM67048

Products Referenced in This Question

Product Page this Question was Asked From

Continue Researching