Does The SolidStep Lift Assist Kit LC733937 Have To Attach To Left Side Of Entry Door?

Question

Question:

Do they make this for right side assist? Thank you

asked by: Stanley K

0

Expert Reply:

I checked with my contact at Lippert and the only two SolidStep Lift Assist Kits currently available both attach to the left hand side of your entry door.

If you have a 26" - 29" wide entry door you will need the # LC733937 and for 30" - 36" wide entry doors you will need the # LC733939.

I included a video of the # LC733939 being installed for you to take a look at.

expert reply by: Samuel C

0

Answer 1

Most likely, yes, the SolidStep Manual Fold-Down Steps #LC791574 would fit without removing the frame mounted steps under the entry door. Customers have done this before, see picture. I have included a link to a video review of these steps for you.

view full answer...

Answer 2

The unit itself is about 10-1/2" in depth when in the upright position. How that translates to depth inside the RV is dependent on installation. This mounts to the threshold of doorway with slight adjustment available. If you set further back on…

view full answer...

Answer 3

I pulled the Lippert SolidStep RV Steps #LC791574 and took some measurements to clear up any confusion. The mounting bracket (part that attaches to the floor) is 21" wide and the the brackets that sit against the door flange can be adjusted by…

view full answer...

Answer 4

That specific portion of the install instructions of the SolidStep Manual Fold Down Steps part #LC791574 refers to the floor covering. Underneath that RVs do all have wood sub floors.

view full answer...

Answer 5

You will be just fine with the SolidStep Manual Fold-Down, #LC791574. This is designed to replace the trim plate. Please see the attached installation video to get a complete visual the installed arrangement. If installed properly your door will…

view full answer...

Answer 6

For a Lippert SolidStep Triple step the part number you'll want is the #LC698799 as it has a doorway width range of 24 to 26 inches which will work great with your doorway that measures 24-1/4 inch. We do not have the lift assist versions of…

view full answer...

Answer 7

The SolidStep Manual Fold-Down Steps for 26" to 29-7/8" RV Door Frames - Quad - Aluminum #LC791574 will work fine with most screen door bars like the Camco Deluxe RV Screen Door Cross Bar - 21-1/4" long to 28-5/8" long - Aluminum…

view full answer...

Answer 8

The TorkLift GlowStep Revolution Scissor Steps w/ Landing Gear #TLA8102 have a height of 16-1/2" from the top of the mounting bracket to the bottom of the steps when fully retracted. This is the same for the #TLA8103 since they both use the same…

view full answer...

Answer 9

I spoke with the manufacturer to ensure the measurements were correct and found that the chart on the page for #LC432690 is incorrect. It does require 27-1/2" of space for the mounting brackets. Both the #LC432690 and #LC432696 will be too big…

view full answer...

Answer 10

Your toy hauler's ground to threshold and opening width dimensions of 25-1/2-inches are just within the mounting requirements for the 3-step TorkLift GlowStep Revolution Scissor Steps #TLA8103. This unit is designed to give an easy drop-in fit as…

view full answer...

Answer 11

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...