Possible Replacement Mounting Hardware For Thule Combibox 250

Question

Question:

will this mounting hardware work with the Thule 250 Combi box? Replacement Mounting Hardware for Thule Weekender Cargo Box Item # 1032802

asked by: Les B

0

Expert Reply:

I checked with Thule for you and they do not have any replacement mounting hardware for a Thule Combibox 250, so we can't confirm a fit for any hardware. That said, mounting hardware can often be made to fit, though it will likely require you to drill new holes in your cargo box.

If you are willing to do that you should be able to use the Replacement Mounting Hardware for Thule Weekender Cargo Box # 1032802.

expert reply by: Kyle S

0

Answer 1

The hardware kit SR04952 that you referenced is no longer available but you might be able to use the Replacement Hardware Kit #TH05603 instead as it uses some of the same hardware. I have attached a picture showing the dimensions of the U-Bolt for…

view full answer...

Answer 2

The only way to remove a Thule lock cylinder like the ones in #TH450400 is by inserting the master key into a cylinder in the unlocked position. However, I have a few tips and tricks to help you remove the broken key to allow for the master key to be…

view full answer...

Answer 3

We do offer a replacement Spring Hinge for the Sears X-Cargo Sport-20 rooftop boxes, part #TH14933. The part #TH14936 you referenced is not an ideal fit for your Sears X-Cargo Sport-20 due to the stiffness of the spring.

view full answer...

Answer 4

The correct mounting hardware for the Sears X-Cargo 20 SV is the part #TH05603. We confirmed this with our contact at Thule who manufactures the Sears boxes.

view full answer...

Answer 5

According to Thule, the correct replacement hinge for your Cascade 1100 cargo box would be #TH13227. The hinges are sold individually. The #TH14936 you referred to is a replacement strut for the newer Cascade XT and would not fit your box.

view full answer...

Answer 6

The Replacement Hardware Kit for Searsbox Cargo Box #TH05603 that you referenced is the correct kit for your Sears X-Cargo Sport 20 cargo box and would be also compatible with the crossbars of your 2017 Subaru Forester so this would be exactly what…

view full answer...

Answer 7

We have recommended in the past for people in similar situations as yours to modify their boxes and install the Hardware part #TH04997 which has much wider U-bolts compatible with factory and aftermarket aero style crossbars. You basically would have…

view full answer...

Answer 8

Yes, you can use the Replacement Hardware Kit for Searsbox Cargo Box #TH05603 to attach your old Thule Sidekick cargo box to your 2018 Subaru Outback Wagon.

view full answer...

Answer 9

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 10

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 11

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 12

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two options.…

view full answer...

Possible Replacement Mounting Hardware For Thule Combibox 250

Product Page this Question was Asked From

Continue Researching