Will Lippert Power Stance Trailer Jack Fit On A-Frame Trailer With Limited Clearance?

Question

Question:

I have a cruiser veiwfinder trailer. Its a v nose. I only have about 2-1/2inch between the jack tube and the front of the trailer. Will this jack work?

asked by: David W

0

Expert Reply:

It sure will!

I had our warehouse measure the Lippert Power Stance Electric Trailer Jack with Footplate - A-Frame - 18" Lift - 3,500 lbs # LC69VR you were looking at and from the back of the jack tube to the back of the head of the jack is 1-1/2" as shown in the included diagram.

I included a video of the # LC69VR for you to take a look at.

expert reply by: Samuel C

0

Dimensions Of Lippert Power Stance Electric Jack # LC69VR
(click to enlarge)

Answer 1

To replace your WF-9865LIS converter I recommend the Progressive Dynamics 9300 Series RV Converter Charger #PD79RR. This converter is compatible with lead acid, AGM, and LiFePO4 batteries and has a 60 amp converter rating. It installs the same way…

view full answer...

Answer 2

The difference between the two models that you were researching is that the #PD9160A is designed for use with lead acid batteries and the #PD9160ALV is designed for use with lithium batteries. Choosing the incorrect battery profile can lead to…

view full answer...

Answer 3

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 4

Hey Richard, thanks for reaching out! The Dexter DX7.5 Drop-N-Go Brake Actuator #099-175-00 is a great option for a replacement actuator because it's a direct replacement for the common Model 60 actuators that were popular in the…

view full answer...

Answer 5

Hey Travis, congrats on the new 2024 Jayco Flight 284BHS! Your travel trailer looks to have a GVWR of 7,950 lbs so I recommend going with the Equal-i-zer Weight Distribution w/ 4-Point Sway Control #EQ37121ET and pairing it with the Shank…

view full answer...

Answer 6

You will have to go with a sliding hitch to allow the trailer to make tight turns. For a trailer 8 feet wide the only bed length that's going to allow 90 degree turns without a slider is a stationary hitch. That being said you have two…

view full answer...

Answer 7

Lippert does not offer a replacement inner jack tube for their jack 1817941. When a jack is damaged in this way (which is more common than you want to know) it really is best to replace the entire jack for safety reasons. The outer tube on your…

view full answer...

Answer 8

Hi Sean, We do offer the Ground Control 3.0 for prepped trailers part number 2021106810 as part #LC52ED. This is going to include the rest of the components needed to complete the system. Since we don't have a video of this kit yet…

view full answer...

Answer 9

We do have the panels separately. What you're looking for is the Go Power Overlander Expansion Kit - 200 Watt Solar Panel #34282182.

view full answer...

Answer 10

Hi Robert, So there isn't one that can be used with a cordless drill (which would be an electric jack only) as all the electric A-frame jacks are all higher than the 12" to 14" you want. There is a manual crank jack you can use which I…

view full answer...

Answer 11

Hi Robert, So I know you don't want to, but the only option for a hitch extension for your 2-1/2 inch hitch does reduce the receiver to 2 inches. I hope you're not mad at me, but there unfortunately is no 2-1/2 inch hitch extender that also…

view full answer...