Measurements of Double Roller Catches with Prongs for RV Cabinets

Question

Question:

Can you tell me the length and width of this product. Both pieces. I have a 2004 four winds 5000 class c. My plastic kitchen drawer latches are broken 2 or 3 of them .

asked by: Jeff

0

Expert Reply:

The requested measurements for the Double Roller Catches with Prongs for RV Cabinets, # 37270235 are 7/8" by 1-11/16".

expert reply by: Michael R

0

Measure_37270235_001
(click to enlarge)

Answer 1

I have listed the measurements for the Double Roller Catches with Prongs for RV Cabinets #37270235 below and included a diagram of each with the measurements. Catch: 1-5/8" tall and 7/8" wide with mounting hole spacing of 1-3/16"…

view full answer...

Answer 2

Yes, the distance between the mounting holes of the Double Roller Catches #37270235 that you referenced is 1-1/4 inches.

view full answer...

Answer 3

It would be pretty hard to find a roller catch set for your cabinets that would not require drilling so the best option we have would be the part #37270235.

view full answer...

Answer 4

You can tow a trailer with a weight distribution setup that does not have the spring bars connected. As long as the head of the system is attached to the shank properly (there's no reason it wouldn't be) it would work just as well as a…

view full answer...

Answer 5

The best way to prevent theft of the Rampage Wireless Backup Camera #RA7710 that you referenced is to remove it from the vehicle when not in use. I attached a review video for this camera for you to check out as well.

view full answer...

Answer 6

I recommend using the Double Roller Catches with Prongs for RV Cabinets - Qty 2 #37270235 because they're constructed of metal instead of the plastic latches you've currently got. This is designed specifically for RVs and the jostling that…

view full answer...

Answer 7

The difference between the Class II and Class III hitches has to do with their Gross Trailer Weight (GTW), their Tongue Weight (TW), and their Hitch Receiver Size. Class II trailer hitch receivers have a 1-1/4 inch receiver and can be rated up to…

view full answer...

Answer 8

In order to determine the torque rating for the lug nuts on your trailer you will need to know check out the chart I attached that shows all of the torque specs for all the trailer lugs available based on stud size, wheel material and wheel size.

view full answer...

Answer 9

A 4-Way trailer connector has the basic lighting functions only; running lights, left turn signal and brake lights, right turn signal and brake lights, and ground. A 7-Way has these functions and a 12 volt circuit, a circuit for electric trailer…

view full answer...

Answer 10

Yes, I have listed for your below the roof rack systems from Rhino-Rack, Thule, and Yakima that will fit the RetraxPRO XR Hard Tonneau Covers like part #RTT-80243 for your 2019 Ram 1500. Rhino-Rack Vortex Crossbar System part #RRVA180B-RRRLT600…

view full answer...

Answer 11

The difference between an load range C and load range D tire in the same size is the capacity and psi rating. The two tires will still have the same dimensions and fit on the same wheel. The D rated tire has a higher capacity. For a ST175/80D13 like…

view full answer...

Answer 12

There is only one difference between the Curt Trailer Hitch Receiver #C13176 and etrailer Trailer Hitch Receiver #e98909 that fit your 2020 Chevrolet Colorado, which is the finish. The Curt trailer hitch has a glossy black finish while the etrailer…

view full answer...

Measurements of Double Roller Catches with Prongs for RV Cabinets

Product Page this Question was Asked From

Featured Help Information

Miscellaneous Media

Continue Researching